Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM D88-07(2013) 1.5.2013 náhľad

Doplňujúce informácie

ASTM D88-07(2013)

Standard Test Method for Saybolt Viscosity

Automaticky preložený názov:

Štandardná skúšobná metóda pre Saybolta Viskozita

NORMA vydaná dňa 1.5.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.00 € Tlačené - 70.00 €
Dostupnosť	SKLADOM
Cena	70.00 € bez DPH
70.00 €

Informácie o norme:

Označenie normy: ASTM D88-07(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2013
Kód tovaru: NS-39581
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Měření objemu, hmotnosti, hustoty, viskozity

Anotácia textu normy ASTM D88-07(2013) :

Keywords:
bituminous materials, kinematic, saybolt, viscosity, ICS Number Code 17.060 (Measurement of volume, mass, density, viscosity)

Doplňujúce informácie

Significance and Use

5.1 This test method is useful in characterizing certain petroleum products, as one element in establishing uniformity of shipments and sources of supply.

5.2 See Guide D117 for applicability to mineral oils used as electrical insulating oils.

5.3 The Saybolt Furol viscosity is approximately one tenth the Saybolt Universal viscosity, and is recommended for characterization of petroleum products such as fuel oils and other residual materials having Saybolt Universal viscosities greater than 1000 s.

5.4 Determination of the Saybolt Furol viscosity of bituminous materials at higher temperatures is covered by Test Method E102.

1. Scope

1.1 This test method covers the empirical procedures for determining the Saybolt Universal or Saybolt Furol viscosities of petroleum products at specified temperatures between 21 and 99°C (70 and 210°F). A special procedure for waxy products is indicated.

1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D4057-22	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
D4177-22e1	Standard Practice for Automatic Sampling of Petroleum and Petroleum Products (Includes all amendments and changes 3/24/2023).
E1-14(2020)	Standard Specification for ASTM Liquid-in-Glass Thermometers
E11-22	Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
E102-93(1997)	Standard Test Method for Saybolt Furol Viscosity of Bituminous Materials at High Temperatures
D93-20	Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D117-22	Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Liquids
D140-01	Standard Practice for Sampling Bituminous Materials
D244-23	Standard Test Methods and Practices for Emulsified Asphalts
D445-23	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D2161-20	Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity
D2170-07	Standard Test Method for Kinematic Viscosity of Asphalts (Bitumens)