Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Measuring Viscosity at High Shear Rate by Tapered Bearing Simulator Viscometer at 100°C
Automaticky preložený názov:
Štandardná skúšobná metóda na meranie viskozity pri vysokej šmykovej rýchlosti by Kuželová ložiská Simulator viskozimetra pri 100 ° C
NORMA vydaná dňa 1.11.2012
Označenie normy: ASTM D6616-07(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2012
Kód tovaru: NS-35900
Počet strán: 13
Približná hmotnosť: 39 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
dynamic viscosity, high shear rate viscosity, high shear rate viscosity at 100°C, high shear viscosity, high temperature viscosity, rotational viscometer, Tapered Bearing Simulator Viscometer, ICS Number Code 17.060 (Measurement of volume, mass, density, viscosity)
Significance and Use | ||||
5.1 Viscosity at the shear rate and temperature of this test method is thought to be particularly representative of bearing conditions in large medium speed reciprocating engines as well as automotive and heavy duty engines operating in this temperature regime. 5.2 The importance of viscosity under these conditions has been stressed in railroad specifications. |
||||
1. Scope | ||||
1.1 This test method covers the laboratory determination of the viscosity of engine oils at 100°C and 1·106s –1 using the Tapered Bearing Simulator (TBS) viscometer.2 1.2 The Newtonian calibration oils
used to establish this test method range from approximately 5 to 12
mPa·s (cP) at 100°C and either the manual or automated protocol was
used by each participant in developing the precision statement. The
viscosity range of the test method at this temperature is from 1
mPa·s (cP) to above 25 mPa·s (cP), depending on the model of
TBS.
1.3 The non-Newtonian reference oil used to establish the shear rate of 1·106s–1 for this test method has a viscosity of approximately 10 mPa·s at 100°C. 1.4 Application to petroleum products other than engine oil has not been determined in preparing the viscometric information for this test method. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. This test method uses the milliPascal second (mPa·s) as the unit of viscosity. This unit is equivalent to the centiPoise (cP), which is shown in parentheses. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. |
||||
2. Referenced Documents | ||||
|
Historická
1.1.2013
Historická
1.10.2009
Historická
1.8.2014
Historická
1.3.2013
Historická
1.11.2012
Historická
15.11.2012
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.