Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Tensile Properties of Thin Plastic Sheeting
Automaticky preložený názov:
Štandardná skúšobná metóda pre mechanických vlastností tenkých plastových fólií
NORMA vydaná dňa 1.8.2012
Označenie normy: ASTM D882-12
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2012
Kód tovaru: NS-39594
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
modulus of elasticity, plastic film, plastic sheeting, tensile properties, tensile strength, toughness, yield stress, ICS Number Code 83.140.10 (Films and sheets)
Significance and Use | ||||||||||||||||||||
4.1 Tensile properties determined by this test method are of value for the identification and characterization of materials for control and specification purposes. Tensile properties can vary with specimen thickness, method of preparation, speed of testing, type of grips used, and manner of measuring extension. Consequently, where precise comparative results are desired, these factors must be carefully controlled. This test method shall be used for referee purposes, unless otherwise indicated in particular material specifications. For many materials, there can be a specification that requires the use of this test method, but with some procedural modifications that take precedence when adhering to the specification. Therefore, it is advisable to refer to that material specification before using this test method. Table 1 in Classification D4000 lists the ASTM materials standards that currently exist. 4.2 Tensile properties can be utilized to provide data for research and development and engineering design as well as quality control and specification. However, data from such tests cannot be considered significant for applications differing widely from the load-time scale of the test employed. 4.3 The tensile modulus of elasticity is an index of the stiffness of thin plastic sheeting. The reproducibility of test results is good when precise control is maintained over all test conditions. When different materials are being compared for stiffness, specimens of identical dimensions must be employed. 4.4 The tensile energy to break (TEB) is the total energy absorbed per unit volume of the specimen up to the point of rupture. In some texts this property has been referred to as toughness. It is used to evaluate materials that are subjected to heavy abuse or that can stall web transport equipment in the event of a machine malfunction in end-use applications. However, the rate of strain, specimen parameters, and especially flaws can cause large variations in the results. In that sense, caution is advised in utilizing TEB test results for end-use design applications. 4.5 Materials that fail by tearing give anomalous data which cannot be compared with those from normal failure. |
||||||||||||||||||||
1. Scope | ||||||||||||||||||||
1.1 This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). 1.2 This test method can be used to
test all plastics within the thickness range described and the
capacity of the machine employed.
1.3 Specimen extension can be measured by grip separation, extension indicators, or displacement of gage marks. 1.4 The procedure for determining the tensile modulus of elasticity is included at one strain rate. 1.5 Test data obtained by this test
method is relevant and appropriate for use in engineering
design.
1.6 The values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Practice for Conditioning Plastics for Testing
|
|
Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
|
|
Standard Classification System for Specifying Plastic Materials
|
|
Standard Terminology Relating to Plastics
|
|
Standard Guide for Determination of Thickness of Plastic Film Test Specimens
|
|
Standard Practice for Cutting Film and Sheeting Test Specimens
|
|
Standard Test Method for Tensile Properties of Plastics
|
ISO 527-3
|
Plastics--Determination of Tensile Properties--Part 3: Test Conditions for Films and Sheets Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
|
|
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
|
|
Standard Practices for Force Calibration and Verification of Testing Machines |
Historická
1.4.2010
Historická
1.2.2011
Historická
1.12.2011
Historická
15.2.2009
Historická
1.7.2008
Historická
1.5.2010
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.