Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
Automaticky preložený názov:
Štandardná prax pre prípravu publikácií Paste tlačiarenské farby s potlačou Gage
NORMA vydaná dňa 1.6.2012
Označenie normy: ASTM D6846-02(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2012
Kód tovaru: NS-36756
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
flat-bed (offset) proof press, paste printing inks, printing gage, printing inks, proofing of inks, ICS Number Code 87.080 (Inks. Printing inks)
Significance and Use | ||||||
4.1 Laboratory proofing of inks is necessary to establish a reproducible prediction of print appearance and performance properties, most of which are highly sensitive to ink film thickness. The apparatus described in this practice has found wide use for routine control proofing because it provides an economical method for producing reasonably large prints at film thicknesses comparable to those obtained on production presses. FIG. 1 Schematic Diagram of
Printing Gages (not drawn to scale)
4.2 A unique advantage of printing gages is that, depending on the design selected, prints can be produced at a range of tapered film thicknesses or at several levels of uniform thicknesses in a single proofing. Because of the built-in film thickness control, ink metering is not necessary. Relatively small quantities of test samples are used, and less than two minutes are required to ink a gage, pull a letterpress print, and clean up. In addition, problems due to ink distribution systems are eliminated, two inks may be proofed at the same time, and multi-color printing is possible. 4.3 This practice does not duplicate the dynamics of a high speed press, nevertheless, it is useful for quality control and for specification acceptance between the producer and the user. |
||||||
1. Scope | ||||||
1.1 This practice covers the procedure for preparing laboratory prints of paste inks using a printing gage in conjunction with a flat-bed proof press. 1.2 This practice is applicable to the preparation of solid-area prints by direct letterpress or by dry offset on a flat substrate such as paper, paperboard, or metal. 1.3 This practice is applicable primarily to lithographic and letterpress inks that dry by oxidation or penetration. With the addition of appropriate drying or curing equipment, it is also applicable to other paste ink systems such as heat-set or energy-curable. 1.4 The instructions in this practice are intended to minimize the within-print and among-operator variability inherent in hand operations. 1.5 This practice features built-in ink film thickness control. It does not measure the film thickness transferred to the print; however, film thickness equivalence may be evaluated by visual or instrumental comparisons of optical density. 1.6 Values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
Standard Test Method for Fineness of
Grind of Printing Inks By the NPIRI Grindometer Standard Practice for Preparing Prints of
Paste Printing Inks Using a Hand Operated Laboratory Flat-Bed
Press Standard Test Method for Relative Setting
of Heatset Printing Inks (Includes all amendments and changes
7/3/2020). |
Historická
1.2.2011
Historická
1.2.2010
Historická
1.12.2010
Historická
1.11.2012
Historická
1.6.2011
Historická
1.6.2008
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-04 (Počet položiek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.