Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D6041-11

Standard Specification for Contact-Molded ´Fiberglass´ (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings

Automaticky preložený názov:

Štandard Specification pre Bezkontaktné Čelní'Fiberglass '(sklenými vláknami vystužený Teplom živice) odolné voči korózii potrubia a armatúry

NORMA vydaná dňa 1.12.2011

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 69.80 € Tlačené - 69.80 €
Dostupnosť	SKLADOM
Cena	69.80 € bez DPH
69.80 €

Informácie o norme:

Označenie normy: ASTM D6041-11
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2011
Kód tovaru: NS-33529
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty
Fitinky z plastické hmoty

Anotácia textu normy ASTM D6041-11 :

Keywords:
chemical resistant, contact molded, fiberglass, fittings, glass-fiber-reinforced thermosetting plastic, pipe, ICS Number Code 23.040.20 (Plastic pipes), 23.040.45 (Plastic fittings)

Doplňujúce informácie

1. Scope

1.1 This specification covers pipe and fittings fabricated by contact molding, for pressures to 150 psi and made of a commercial-grade polyester resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance.

1.2 This specification does not cover resins other than polyester, reinforcing materials other than glass fibers or fabrication methods other than contact molding.

Note 1—For the purposes of this specification, the term polyester resin will include both polyester and vinylester resins.

1.3 This specification does not cover the design of pipe and fittings intended for use with liquids heated above their flash points.

1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are provided for information purposes only.

1.5 The following precautionary caveat pertains only to Section 10, the test methods portion, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 2—There is no known ISO equivalent to this standard.

2. Referenced Documents

B18.22	Type B Narrow Washers
F412-23	Standard Terminology Relating to Plastic Piping Systems
D5421-23	Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges
D3681-23	Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
D3567-17(2022)	Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D2584-18	Standard Test Method for Ignition Loss of Cured Reinforced Resins
D2583-13	Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D883-24	Standard Terminology Relating to Plastics
D638-22	Standard Test Method for Tensile Properties of Plastics
D618-21	Standard Practice for Conditioning Plastics for Testing
C582-23	Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment
C581-20	Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
NSF Standard 61 Drinking Water System Components—Health Effects Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings