Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D3839-14

Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe

Automaticky preložený názov:

Štandardné Sprievodca pre podzemný komplex a ldquo, CSF-rdquo; (Vystuženého sklenenými vláknami Teplom-živice) Pipe

NORMA vydaná dňa 1.3.2014

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 87.30 € Tlačené - 87.30 €
Dostupnosť	SKLADOM
Cena	87.30 € bez DPH
87.30 €

Informácie o norme:

Označenie normy: ASTM D3839-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2014
Kód tovaru: NS-25051
Počet strán: 12
Približná hmotnosť: 36 g (0.08 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty

Anotácia textu normy ASTM D3839-14 :

Keywords:

backfill, bedding, fiberglass pipe, haunching, soil stiffness, underground installation, ICS Number Code 23.040.20 (Plastic pipes)

Doplňujúce informácie

Significance and Use

4.1 This practice is for use by designers and specifiers, manufacturers, installation contractors, regulatory agencies, owners, and inspection organizations involved in the construction of buried fiberglass pipelines. As with any practice, modifications may be required for specific job conditions, or for special local or regional conditions. Recommendations for inclusion of this practice in contract documents for a specific project are given in Appendix X1.

1. Scope

1.1 This practice establishes procedures for the burial of pressure and nonpressure “fiberglass” (glass-fiber-reinforced thermosetting-resin) pipe in many typically encountered soil conditions. Included are recommendations for trenching, placing pipe, joining pipe, placing and compacting backfill, and monitoring deflection levels. Guidance for installation of fiberglass pipe in subaqueous conditions is not included.

1.2 Product standards for fiberglass pipe encompass a wide range of product variables. Diameters range from 1 in. to 13 ft (25 mm to 4000 mm) and pipe stiffnesses range from 9 to over 72 psi (60 to 500 kPa) with internal pressure ratings up to several thousand pound force per square inch. This standard does not purport to consider all of the possible combinations of pipe, soil types, and natural ground conditions that may occur. The recommendations in this practice may need to be modified or expanded to meet the needs of some installation conditions. In particular, fiberglass pipe with diameters of a few inches are generally so stiff that they are frequently installed in accordance with different guidelines. Consult with the pipe manufacturer for guidance on which practices are applicable to these particular pipes.

1.3 The scope of this practice excludes product-performance criteria such as a minimum pipe stiffness, maximum service deflection, or long-term strength. Such parameters may be contained in product standards or design specifications, or both, for fiberglass pipe. It is incumbent upon the specified product manufacturer or project engineer to verify and ensure that the pipe specified for an intended application, when installed in accordance with procedures outlined in this practice, will provide a long-term, satisfactory performance in accordance with criteria established for that application.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D8-22a	Standard Terminology Relating to Materials for Roads and Pavements (Includes all amendments and changes 6/15/2022).
D653-22	Standard Terminology Relating to Soil, Rock, and Contained Fluids
D698-12(2021)	Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft3 (600 kN-m/m3))
D883-24	Standard Terminology Relating to Plastics
D1556-07	Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method
D2167-15	Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method (Withdrawn 2024)
D2216-19	Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
AWWA	Manual of Practice M45 Fiberglass Pipe Design Manual Available from American Water Works Association (AWWA), 6666 W. Quincy Ave., Denver, CO 80235, http://www.awwa.org.
D4959-24	Standard Test Method for Determination of Water Content of Soil By Direct Heating
D5030-04	Standard Test Method for Density of Soil and Rock in Place by the Water Replacement Method in a Test Pit
D5080-20	Standard Test Method for Rapid Determination of Percent Compaction
D5821-13(2017)	Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
D2488-17e1	Standard Practice for Description and Identification of Soils (Visual-Manual Procedures) (Includes all amendments and changes 4/4/2018).
F1668-16(2022)	Standard Guide for Construction Procedures for Buried Plastic Pipe
AASHTO LRFD	Bridge Design Specifications, 2nd Edition, American Association of State Highway and Transportation Officials Available from American Association of State Highway and Transportation Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001.
AASHTO M145	Classification of Soils and Soil Aggregate Mixtures
D6938-23	Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)
D7382-20	Standard Test Methods for Determination of Maximum Dry Unit Weight of Granular Soils Using a Vibrating Hammer
F412-23	Standard Terminology Relating to Plastic Piping Systems
D4253-16e1	Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table (Includes all amendments and changes 11/21/2019).
D4254-16	Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
D4318-17e1	Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils (Includes all amendments and changes 4/17/2018).
D4564-08	Standard Test Method for Density and Unit Weight of Soil in Place by the Sleeve Method
D4643-17	Standard Test Method for Determination of Water Content of Soil and Rock by Microwave Oven Heating
D4914-08	Standard Test Methods for Density and Unit Weight of Soil and Rock in Place by the Sand Replacement Method in a Test Pit
D4944-18	Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester
D2487-17e1	Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) (Includes all amendments and changes 4/2/2020).