Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM D5813-04(2012) 1.10.2012 náhľad

Doplňujúce informácie

ASTM D5813-04(2012)

Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems

Automaticky preložený názov:

Štandard Specification pre tvrdených-In-Place Teplom Plastové kanalizačné potrubné systémy

NORMA vydaná dňa 1.10.2012

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 64.50 € Tlačené - 64.50 €
Dostupnosť	SKLADOM
Cena	64.50 € bez DPH
64.50 €

Informácie o norme:

Označenie normy: ASTM D5813-04(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2012
Kód tovaru: NS-32660
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty

Anotácia textu normy ASTM D5813-04(2012) :

Keywords:

cured-in-place pipe (CIPP), plastic pipe&mdash,thermoset, rehabilitation, thermosetting resin pipe, underground installation, ICS Number Code 23.040.20 (Plastic pipes)

Doplňujúce informácie

1. Scope

1.1 This specification covers cured-in-place thermosetting resin pipe (CIPP), 4 through 132-in. (100 through 3353-mm) equivalent diameter, for use in gravity flow systems for conveying sanitary sewage, storm water, and certain industrial wastes. This specification is suited for the evaluation and testing of materials used in the rehabilitation of existing pipes by the installation and cure of a resin-impregnated fabric liner.

1.2 This specification can also be extended to cover manholes, pump stations, wetwells, vaults, storage tanks, and other similar structures where a cured in place liner using thermosetting resin is applicable.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D638-22	Standard Test Method for Tensile Properties of Plastics
D695-23	Standard Test Method for Compressive Properties of Rigid Plastics
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D883-24	Standard Terminology Relating to Plastics
D543-21	Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
	Methods of Test for Breaking Load and Elongation of Textile Fabrics Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
D3039/D3039M-17	Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
D3567-17(2022)	Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D3681-23	Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
F2019-22	Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
D4814-23a	Standard Specification for Automotive Spark-Ignition Engine Fuel (Includes all amendments and changes 12/14/2023).
F412-23	Standard Terminology Relating to Plastic Piping Systems
F1216-22	Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
F1743-22	Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)

Odporúčame:

EviZak - všetky zákony vrátane ich evidencie na jednom mieste

Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !

Chcete vedieť viac informácii ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.