Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F1901-10

Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems

Automaticky preložený názov:

Štandard Specification pre polyetylénu (PE) rúrky a tvarovky pre strešné odvodňovacie systémy

NORMA vydaná dňa 1.8.2010

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 79.80 € Tlačené - 79.80 €
Dostupnosť	SKLADOM
Cena	79.80 € bez DPH
79.80 €

Informácie o norme:

Označenie normy: ASTM F1901-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2010
Kód tovaru: NS-52026
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Potrubí a součásti potrubí obecně

Anotácia textu normy ASTM F1901-10 :

Keywords:

DWV, pipe fittings, pipes, plastic pipes, polyethylene, recycle, waste disposal (building), Drain/waste/vent (DWV)--polyethylene (PE), Polyethylene (PE) pipe--specifications, Roofing membranes--specifications, ICS Number Code 23.040.01 (Pipeline components in general. Pipelines)

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements for polyethylene (PE) pipe and fittings for nonpressure roof drain systems.

1.2 This specification covers pipe and fittings intended for normal residential and commercial uses and is not intended for use in unusual corrosive conditions.

Note 1—Before installing pipe for waste disposal use, the approval of the cognizant building code authority shall be obtained as conditions not found in normal use or temperatures approaching 140°F (60°C) may be encountered.

1.3 Pipe is produced in dimensions based on outside diameters of 32 mm (1.250 in.) and larger in accordance with Specification F714.

1.4 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.

1.5 Pipe and fittings are joined by the heat-fusion method, by the electrofusion method, or by using mechanical joints (excluding insert fittings) recommended by the manufacturer.

1.6 In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10). In all cases, the values given in parentheses are provided for information only.

1.7 The following safety hazards caveat pertains only to the test method, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
B36.10	Standard Dimensions of Steel Pipe (IPS)
F2620-20ae2	Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings (Includes all amendments and changes 3/17/2022).
F1498-08(2020)	Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
D4976-12a(2020)	Standard Specification for Polyethylene Plastics Molding and Extrusion Materials (Includes all amendments and changes 11/17/2022).
D5033-00	Standard Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics (Withdrawn 2007)
F412-23	Standard Terminology Relating to Plastic Piping Systems
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
D570-22	Standard Test Method for Water Absorption of Plastics
D618-21	Standard Practice for Conditioning Plastics for Testing
F1290-19	Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
3607	Polyethylene Pipe: Tolerances on Outside Diameters and Wall Thicknesses
161	Thermoplastic Pipe for the Transport of FluidsNominal Outside Diameters and Nominal Pressures
MIL-STD-129	Marking for Shipment and Storage
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
D3311-22	Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
F714-24	Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
D543-21	Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents

Podobné normy:

ASTM C12-13a

Historická
1.12.2013

ASTM C1409-12

Historická
1.9.2012

ASTM C828-11

Historická
1.9.2006

ASTM D7230-06(2013)..

Historická
1.7.2013

ASTM E273-10

Historická
1.6.2010

ASTM F1155-10

Historická
15.12.2010

Odporúčame:

EviZak - všetky zákony vrátane ich evidencie na jednom mieste

Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !

Chcete vedieť viac informácii ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.