Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
Automaticky preložený názov:
Štandardná prax pre rehabilitáciu existujúcich plynovodov a potrubí od vytiahol-in-place Montáž tvrdených-in-Place živicou tvrditeľný teplom potrubia (CIPP)
NORMA vydaná dňa 1.11.2008
Označenie normy: ASTM F1743-08
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2008
Kód tovaru: NS-51383
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
cured-in-place pipe, installation´underground, plastic pipe´thermoset, rehabilitation, thermosetting resin pipe, CIPP (cured-in-place thermosetting resin pipe), Conduits, Installation--plastic pipe materials/applications, Rehabilitation--sewerlines, Resin-impregnated tube, Thermosetting plastic pipe/tubing/fittings, ICS Number Code 23.040.20 (Plastic pipes)
Significance and Use | ||||||||||||||||||||||||||||||
This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of conduits through the use of a resin-impregnated fabric tube pulled-in-place through an existing conduit and secondarily inflated through the inversion of a calibration hose. Modifications may be required for specific job conditions. |
||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||
1.1 This practice describes the procedures for the reconstruction of pipelines and conduits (4 to 96 in. (10 to 244 cm) diameter) by the pulled-in-place installation of a resin-impregnated, flexible fabric tube into an existing conduit and secondarily inflated through the inversion of a calibration hose by the use of a hydrostatic head or air pressure (see Fig. 1). The resin is cured by circulating hot water or by the introduction of controlled steam into the tube. When cured, the finished cured-in-place pipe will be continuous and tight fitting. This reconstruction process may be used in a variety of gravity and pressure applications such as sanitary sewers, storm sewers, process piping, electrical conduits, and ventilation systems. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.e values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for informational purposes only. Note 1—There are no ISO standards covering the primary subject matter of this practice. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||
|
Historická
1.8.2010
Historická
25.4.2014
Historická
15.11.2011
Historická
1.8.2012
Historická
1.8.2011
Historická
1.5.2014
Posledná aktualizácia: 2024-12-23 (Počet položiek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.