Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F1412-09

Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems

Automaticky preložený názov:

Štandard Specification pre Polyolefín potrubia a tvaroviek pre agresívne odpadov drenážny systém

NORMA vydaná dňa 15.1.2009

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 76.30 € Tlačené - 76.30 €
Dostupnosť	SKLADOM
Cena	76.30 € bez DPH
76.30 €

Informácie o norme:

Označenie normy: ASTM F1412-09
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.1.2009
Kód tovaru: NS-50202
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty

Anotácia textu normy ASTM F1412-09 :

Keywords:

acid waste, corrosion resistance, corrosive waste, drainage, drain pipes, installation, joints, laboratory piped services, pipe fittings, pipes, plastic pipes, polyethylene, polyolefin, polypropylene, thermoplastic polymers, traps (drainage), waste disposal (building), Acid waste, Corrosive service applications--plastics, Drainage materials/systems--specifications, Installation--plastic pipe materials/applications, Laboratory piped services, Nonpressure piping--specifications

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems.

1.2 Pipe is produced in Schedule 40 and 80 IPS sizes in two polyolefins, polyethylene (PE) and polypropylene (PP).

1.3 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.

1.4 Pipe and fittings are joined by the heat fusion method (D 2657 and F 1290) or by using mechanical joints recommended by the manufacturer.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 The following safety hazards caveat pertains only to the test method, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
Uniform Plumbing Code Available from International Association of Plumbing and Mechanical Officials, 5001 E. Philadelphia St., Ontario, CA 91761, http://www.iapmo.org.
MIL-STD-129	Marking for Shipment and Storage
D543-21	Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D3311-22	Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
D2657-07(2023)	Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
F2620-20ae2	Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings (Includes all amendments and changes 3/17/2022).
F1498-08(2020)	Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
F1290-19	Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
F412-23	Standard Terminology Relating to Plastic Piping Systems
D4101-24	Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
D570-22	Standard Test Method for Water Absorption of Plastics
D618-21	Standard Practice for Conditioning Plastics for Testing
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

Podobné normy:

ASTM F2969-12

Historická
1.8.2012

ASTM F2986-12

Historická
15.11.2012

ASTM F2987-12

Historická
1.11.2012

ASTM F2994-13

Historická
1.8.2013

ASTM F402-05(2012)..

Historická
1.2.2012

ASTM F405-13

Historická
1.8.2013

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.