Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) IPS Dimensioned Pressure Pipe
Automaticky preložený názov:
Štandardné špecifikácie pre akrylonitril-butadién-styrén (ABS), IPS Určené tlakového potrubia
NORMA vydaná dňa 1.8.2012
Označenie normy: ASTM F2969-12
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2012
Kód tovaru: NS-54797
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
ABS, HDB, plastic pipe, pressure piping, SDR, ICS Number Code 23.040.20 (Plastic pipes)
1. Scope | ||||||||||||||||||||
1.1 This specification covers acrylonitrile-butadiene-styrene (ABS) IPS dimensioned pressure pipe produced by single extrusion in standard thermoplastic pipe dimension ratios and pressure rated for water (see Appendix X1). Included are criteria for classifying ABS plastic pipe materials and ABS plastic pipe, a system of nomenclature for ABS plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, burst pressure, and extrusion quality. Methods of marking are also given. 1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids, which are chemically compatible with the piping materials. Consult with the manufacturer and local building codes before use in other applications. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing. 1.3 Pipe meeting the requirements of
this standard is not compatible with DWV fittings. The ABS pipe
covered in this standard is intended for pressure service and it
shall be joined to pressure fittings. Non-pressure fittings, such
as DWV fittings from any material (ABS, PVC, CPVC, etc.) are not
acceptable for pressure applications.
1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.6 The following safety hazards
caveat pertains only to the test method portion, Section
Standard Practice for Conditioning
Plastics for Testing Standard Test Method for Time-to-Failure
of Plastic Pipe Under Constant Internal Pressure Standard Test Method for Resistance to
Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and
Fittings Standard Terminology for Abbreviated
Terms Relating to Plastics (Withdrawn 2024) MIL-STD-129 Marking for Shipment and Storage Standard Terminology Relating to Plastic
Piping Systems Standard Test Method for Determining
Dimensions of Thermoplastic Pipe and Fittings Standard Test Method for Obtaining
Hydrostatic Design Basis for Thermoplastic Pipe Materials or
Pressure Design Basis for Thermoplastic Pipe Products Standard Classification System and Basis
for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS)
Materials for Pipe and Fittings |
Historická
1.3.2007
Historická
15.3.2007
Historická
1.3.2014
Historická
1.8.2014
Historická
1.2.2011
Historická
1.2.2013
Posledná aktualizácia: 2024-11-01 (Počet položiek: 2 208 817)
© Copyright 2024 NORMSERVIS s.r.o.