ASTM F1901-10
ASTM F2349-04(2010)..
ASTM F2536-06b(2011)..
ASTM F2769-10
ASTM F2805-11
ASTM F2984-13
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM F1397-93(2012)
Standard Test Method for Determination of Moisture Contribution by Gas Distribution System Components
Automaticky preložený názov:
Štandardná skúšobná metóda na stanovenie vlhkosti Príspevok plynovú distribučnej sústavy komponenty
NORMA vydaná dňa 1.7.2012
Informácie o norme:
Označenie normy: ASTM F1397-93(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2012
Kód tovaru: NS-50150
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM F1397-93(2012) :
Keywords:
components, contamination, gas distribution, moisture analyzer, moisture contribution, semiconductor processing, water outgassing, ICS Number Code 23.040.01 (Pipeline components in general. Pipelines)
Doplňujúce informácie
| Significance and Use |
|
3.1 The purpose of this test method is to define a procedure for testing components being considered for installation into a high-purity gas distribution system. Application of this test method is expected to yield comparable data among components tested for the purposes of qualification for this installation. |
| 1. Scope |
|
1.1 This test method covers testing components for total moisture contribution to a gas distribution system at ambient temperature. In addition, the test method allows testing at elevated ambient temperatures as high as 70°C and of the component moisture capacity and recovery. 1.2 This test method applies to in-line components containing electronics grade materials such as those used in semiconductor gas distribution systems. 1.3 Limitations: 1.3.1 This test method is limited by the sensitivity of current instrumentation, as well as by the response time of the instrumentation. This test method is not intended to be used for test components larger than 12.7-mm (1/2-in.) outside diameter nominal size. This test method could be applied to larger components; however, the stated volumetric flow rate may not provide adequate mixing to ensure a representative sample. Higher flow rates may improve the mixing but excessively dilute the sample. 1.3.2 This test method is written with the assumption that the operator understands the use of the apparatus at a level equivalent to six months of experience. 1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 5. |
Podobné normy:
Historická
1.8.2010
Historická
1.5.2010
Historická
1.2.2011
Historická
1.8.2010
Historická
1.8.2011
Historická
1.12.2013
Odporúčame:
EviZak - všetky zákony vrátane ich evidencie na jednom mieste
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
