Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Fabrication and Control of Metal, Other than Aluminum, Reference Blocks Used in Ultrasonic Testing (Withdrawn 2019)
Automaticky preložený názov:
Štandardná prax pre výrobu a kontrolu kovov, iné ako hliník, referenčné bloky použiť pri skúškach ultrazvukovom
NORMA vydaná dňa 1.6.2013
Označenie normy: ASTM E428-08(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2013
Kód tovaru: NS-46750
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
area-amplitude reference blocks, distance-amplitude reference blocks, metal alloy reference blocks, nondestructive testing, ultrasonic reference blocks, ICS Number Code 77.040.20 (Non-destructive testing of metals)
Significance and Use | ||||||
5.1 Reference blocks fabricated in accordance with this practice will exhibit specific area-amplitude and distance-amplitude relationships only with an immersion test at 5 MHz using the search unit, test instrument and test parameters described in this practice. Comparison test at other frequencies or with uncalibrated instruments will not necessarily give the same relationships shown in this practice. See Reference (1) for area-amplitude limitations at other frequencies and transducer diameters. Also see Reference (1.1 This practice covers a procedure for fabrication and control of metal alloy reference blocks used in ultrasonic examination that have a flat-surface sound entry, are cylindrical in shape, and contain flat-bottom holes (FBH) which may be used for checking the performance of ultrasonic examination instrumentation and search units and for standardization and control of ultrasonic examination of metal alloy products. The reference blocks described are suitable for use with either the direct-contact method or immersion pulse-echo ultrasonic methods. 1.2 While this procedure is
basically designed for the fabrication and control of carbon and
alloy steel blocks to be used in conjunction with the examination
of these materials, the fabrication and control procedures may also
be suitable for the preparation of blocks for other types of
materials such as nickel-base alloys, certain types of aluminum
alloys, and so forth. Additional procedures and controls may be
required when fabricating reference blocks from other than carbon
or alloy steel material. This practice shall in no way preclude the
specification or addition of any supplemented requirements as
deemed necessary for the specific application. This practice,
however, must not be confused with, nor does it supersede Practice
E127, specifically governing the fabrication and evaluation of
7075-T6 aluminum alloy ultrasonic standard reference blocks.
1.3 The values stated in inch-pound
units are to be regarded as standard. The values given in
parentheses are mathematical conversions to SI units that are
provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
2. Referenced Documents | ||||||
|
Historická
1.3.2012
Historická
1.5.2012
Historická
1.3.2012
Historická
1.3.2012
Historická
1.5.2012
Historická
1.9.2012
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-23 (Počet položiek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.