ASTM D5117-09
ASTM D5448/D5448M-11..
ASTM D5467/D5467M-97..
ASTM D5528-13
ASTM D5573-99(2012)..
ASTM D5766/D5766M-11..
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D6818-14
Standard Test Method for Ultimate Tensile Properties of Rolled Erosion Control Products
Automaticky preložený názov:
Štandardná skúšobná metóda pre maximálnu mechanických vlastností valcovaného Protierózne produkty
NORMA vydaná dňa 1.5.2014
Informácie o norme:
Označenie normy: ASTM D6818-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2014
Kód tovaru: NS-36650
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D6818-14 :
Keywords:
breaking force, elongation, rolled erosion control products, ICS Number Code 83.120 (Reinforced plastics)
Doplňujúce informácie
| Significance and Use | ||||||||
|
5.1 The strip test in this test method is considered satisfactory for acceptance testing of commercial shipments of Rolled Erosion Control Products since the method has been used extensively in the trade for acceptance testing. 5.1.1 In case of disagreement arising from differences in reported test values when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimen which are as homogeneous as possible and are from a lot of material of the type in question. The test specimen should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before testing is begun. If bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future results in the light of the known bias. |
||||||||
| 1. Scope | ||||||||
|
1.1 This test method covers strip test procedures for determining the tensile properties of Rolled Erosion Control Products (RECP). 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard does not apply to RECP's made of composite materials where the component providing the reinforcement cannot be tested for tensile strength with the procedure herein described. In this case, the established ASTM testing method, which is most appropriate for that material, shall be used instead. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||
| 2. Referenced Documents | ||||||||
|
Podobné normy:
Historická
1.9.2009
Historická
15.11.2011
Historická
1.10.2010
Historická
1.10.2013
Historická
1.10.2012
Historická
1.1.2011
Odporúčame:
EviZak - všetky zákony vrátane ich evidencie na jednom mieste
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
