Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Methods for Rubber Compounding Materials—Determination of Particle Size Distribution of Recycled Vulcanizate Particulate Rubber
Automaticky preložený názov:
Štandardné skúšobné metódy pre gumové zlučovanie Materiály & ndash; Stanovenie Distribúcia veľkosti častíc recyklovaného vulkanizantu častíc kaučuku
NORMA vydaná dňa 1.11.2013
Označenie normy: ASTM D5644-01(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2013
Kód tovaru: NS-32010
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
particle size distribution, recycled vulcanizate particulate rubber, ultrasonic light optical microscopic technique, ICS Number Code 83.060 (Rubber)
Significance and Use | ||||||||||||||||||||
4.1 The particulate size distribution of vulcanizate particulate rubber is used for the purpose of assigning a product mesh or average particle size designation. 4.2 The product designation for mesh size for the Ro-tap method (Method A, as follows) is based on the size designation screen which allows a range for the upper limit retained of maximum 5 % for up to 850 μm (20 mesh) particles, maximum 10 % for 600 to 150 μm (30 to 100 mesh), and maximum 15 % for 128 to 75 μm (120 to 200 mesh). No rubber particles shall be retained on the zero screen (see Table 1, Classification D5603). 4.3 For Method A, the weight percent retained on a specific screen is noted whereas in Method B (ultrasonic technique), the number of particles at a particular size is counted. 4.4 Method B addresses problems that may be caused by tackiness and static electrical forces that recycled rubber particles exert on each other to form agglomerates, especially for 80 mesh or finer particles. This method eliminates agglomerate formation by ultrasonically dispersing the particles. 4.5 Both methods can be used as a quality control tool. |
||||||||||||||||||||
1. Scope | ||||||||||||||||||||
1.1 These test methods describe the procedures for determining average particle size distribution of recycled vulcanizate particulate. 1.2 Method A describes the Ro-tap sieve test method for 60 mesh or coarser particles. 1.3 Method B describes the ultrasonic technique combined with optical microscope especially suitable for 80 mesh or finer particles. This procedure is based on Test Method D3849. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||
|
Historická
15.5.2014
Historická
1.5.2012
Historická
1.1.2012
Historická
15.12.2011
Historická
1.7.2009
Historická
15.5.2014
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.