Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints
Automaticky preložený názov:
Štandardné skúšobné metódy pre stanovenie účinnosti prenosu v rámci Všeobecnej výrobných podmienok na nástrek farieb
NORMA vydaná dňa 1.6.2011
Označenie normy: ASTM D5286-01(2011)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2011
Kód tovaru: NS-30588
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
general production conditions, solvent emission, spray applied coatings, transfer efficiency, VOC, volatile conten, General production conditions, Paint solids, Solid phase materials--paints/related coatings/materials, Solvent emissions, Spray-applied coatings, Transfer efficiency (TE), Volatile organic compounds (VOC)--paints/related coatings, ICS Number Code 87.040 (Paints and varnishes)
Significance and Use | ||||||||||||||||||
Subject to the limitations listed in 1.3, these test methods can be used to optimize paint application processes. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1 These test methods cover the determination of the transfer efficiency of spray-applied coatings under general plant conditions. Transfer efficiency is the ratio of paint solids deposited to the total paint solids used during the application process, expressed as a percent. 1.2 The transfer efficiency is calculated from the weight or volume of the paint solids sprayed and that of the paint solids deposited on the painted part. 1.3 Limitations include the ability to accurately determine the amount of paint solids deposited on the part and the capability of accurate measurement of the amount of paint sprayed. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Note 1—These test methods apply to general plant production equipment and procedures. A method specific to automotive plants is defined in Test Method D5066. Note 2—The relationship between volatile organic compound emission rates and transfer efficiency in automobile and light duty truck topcoat operations, EPA 450/3-88-01, referenced in Test Method D5066 does not apply to general production facilities. Note 3—A single-point transfer efficiency measurement may not represent the entire process. Note 4—The operator and the spray-application equipment-operating conditions during the transfer efficiency measurement should be representative of normal operating conditions. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements see Section 7, and 10.3.1. Note 5—These test methods have not been adopted by federal regulatory agencies for demonstration of compliance with air pollution regulations such as VOC, HAPS, etc. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Historická
1.7.2014
Historická
1.12.2010
Historická
1.6.2007
Historická
1.7.2010
Historická
1.7.2014
Historická
1.6.2010
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.