Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Determining In Situ Creep Characteristics of Rock (Withdrawn 2017)
Automaticky preložený názov:
Štandardná skúšobná metóda pre stanovenie in situ creepové Charakteristika of Rock
NORMA vydaná dňa 1.7.2008
Označenie normy: ASTM D4553-08
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2008
Kód tovaru: NS-27682
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Zemní práce. Hloubicí práce. Budování základů. Podzemní práce
Keywords:
creep, deformation, in situ stress, loading tests, rigid plate loading method, Creep--rock, Deformation--rock, Destructive testing--soil/rock, Field testing--rock, Fracture testing--rock, Loading tests--rock/related materials, Pressure testing--rock, Rock materials/properties/analysis, Stress--rock, Structural rock, ICS Number Code 93.020 (Earth works. Excavations. Foundation construction. Underground works)
Significance and Use | ||||||||
Results of this test method are used to predict time-dependent deformation characteristics of a rock mass resulting from loading. It is a test that may be required depending on rock type or anticipated loads, or both. This test method may be useful in structural design analysis where loading is applied over an extensive period. This test method is normally performed at ambient temperature, but equipment can be modified or substituted for operations at other temperatures. Results of this test method may be useful in verifying laboratory creep data and structural mathematical modeling analyses. Creep characteristics are determined under a nonuniform state of stress. If during a field investigation, time-dependent characteristics are detected, then an in situ creep test shall be performed. Note 1—The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D 3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D 3740 provides a means of evaluating some of those factors. |
||||||||
1. Scope | ||||||||
1.1 This test method covers the preparation, equipment, test procedure, and data documentation for determining in situ creep characteristics of a rock mass using a rigid plate subjected to controlled loading. 1.2 This test method is designed to be conducted in an underground opening; however, with suitable modifications, this test could be conducted at the surface. 1.3 The test is usually conducted parallel or perpendicular to the anticipated axis of thrust, as dictated by the design load or other orientations, based upon the application. 1.4 Flexible plate apparatus can be used if the anticipated creep displacement is within the tolerance of the travel of the flat jacks. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precaution statements, see Section 8. |
||||||||
2. Referenced Documents | ||||||||
|
Historická
15.1.2013
Historická
15.1.2013
Historická
1.7.2006
Historická
1.6.2014
Historická
1.4.2012
Historická
1.1.2011
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.