Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D4101-14

Standard Specification for Polypropylene Injection and Extrusion Materials

Automaticky preložený názov:

Štandard Specification pre polypropylén vstrekovanie a vytlačovanie materiálov

NORMA vydaná dňa 1.3.2014

Jazyk
Prevedenie	Online zabezpečené PDF - 81.60 € Tlačené - 81.60 €
Dostupnosť	SKLADOM
Cena	81.60 € bez DPH
81.60 €

Informácie o norme:

Označenie normy: ASTM D4101-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2014
Kód tovaru: NS-26049
Počet strán: 17
Približná hmotnosť: 51 g (0.11 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Termoplasty

Anotácia textu normy ASTM D4101-14 :

Keywords:

injection and extrusion materials, materials specification, polypropylene, polypropylene test methods, recycled plastics, ICS Number Code 83.080.20 (Thermoplastic materials)

Doplňujúce informácie


1. Scope
1.1 This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of homopolymer, copolymers, and elastomer compounded with or without the addition of impact modifiers (ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber), colorants, stabilizers, lubricants, or reinforcements. 1.2 This specification allows for the use of those polypropylene materials that can be recycled, reconstituted, and reground, provided that: (1) the requirements as stated in this specification are met, and (2) the material has not been modified in any way to alter its conformance to food contact regulations or similar requirements. The proportions of recycled, reconstituted, and reground material used, as well as the nature and the amount of any contaminant, cannot be practically covered in this specification. It is the responsibility of the supplier and the buyer of recycled, reconstituted, and reground materials to ensure compliance. (See Guide D7209.) 1.3 The values stated in SI units are to be regarded as the standard. 1.4 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
D3641-21	Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
D883-24	Standard Terminology Relating to Plastics
D3835-16	Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
D3763-23	Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
D3801-20a	Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position (Includes all amendments and changes 9/11/2020).
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
D4000-23	Standard Classification System for Specifying Plastic Materials
D149-20	Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
D256-23e1	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023).
D257-14(2021)e1	Standard Test Methods for DC Resistance or Conductance of Insulating Materials (Includes all amendments and changes 5/6/2021).
D523-14(2018)	Standard Test Method for Specular Gloss
D543-21	Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D648-18	Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D746-20	Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
D1435-20	Standard Practice for Outdoor Weathering of Plastics
D1531-06	Standard Test Methods for Relative Permittivity (Dielectric Constant) and Dissipation Factor by Fluid Displacement Procedures (Withdrawn 2012)
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D2565-23	Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
D2584-18	Standard Test Method for Ignition Loss of Cured Reinforced Resins
D2863-23	Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)
D2990-17	Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique
D1525-17e1	Standard Test Method for Vicat Softening Temperature of Plastics (Includes all amendments and changes 9/15/2017).
D696-16	Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C with a Vitreous Silica Dilatometer
D732-17	Standard Test Method for Shear Strength of Plastics by Punch Tool
D785-23	Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
C177-19e1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
D150-22	Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
D495-22	Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
D570-22	Standard Test Method for Water Absorption of Plastics
SAE J1976
D6110-18	Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
D6290-19	Standard Test Method for Color Determination of Plastic Pellets
D7209-06	Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
D4329-21	Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics
D4364-13(2022)e1	Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight (Includes all amendments and changes 2/25/2022).
D4805-88(1994)e1	Standard Terminology for Plastics Standards (Withdrawn 2002)
D4812-19e1	Standard Test Method for Unnotched Cantilever Beam Impact Resistance of Plastics (Includes all amendments and changes 5/3/2022).
D5279-21	Standard Test Method for Plastics: Dynamic Mechanical Properties: In Torsion
D5420-21	Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
D5630-22	Standard Test Method for Ash Content in Plastics
D5740-18	Standard Guide for Writing Material Standards in the Classification D4000 Format
E313-20	Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
E831-19	Standard Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis
MIL-STD-105	Sampling Procedure and Tables for Inspection by Attributes Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094.


SAE J1545	Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Color Trim
	Instrumental Color Difference Measurement for Colorfastness of Automotive Interior Trim Materials
SAE J2412	Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Xenon-Arc Apparatus
SAE J2527	Performance Based Standard for Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Xenon-Arc Apparatus
D5947-18	Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
D618-21	Standard Practice for Conditioning Plastics for Testing
D635-22	Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
D638-22	Standard Test Method for Tensile Properties of Plastics
D695-23	Standard Test Method for Compressive Properties of Rigid Plastics
D1822-21	Standard Test Method for Determining the Tensile-Impact Resistance of Plastics
D2117-82(1988)e1	Standard Test Method for Melting Point of Semicrystalline Polymers by the Hot Stage Microscopy Method (Withdrawn 1994)
D3012-19	Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven
D3418-21	Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry

Podobné normy:

ASTM D3749-13

Historická
1.11.2013

ASTM D3826-98(2013)..

Historická
1.2.2013

ASTM D3835-08

Historická
1.12.2008

ASTM D3895-07

Historická
1.4.2007

ASTM D3935-09

Historická
15.4.2009

ASTM D4066-13

Historická
1.7.2013

Odporúčame:

EviZak - všetky zákony vrátane ich evidencie na jednom mieste

Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !

Chcete vedieť viac informácii ? Pozrite sa na túto stránku.