ASTM D3749-13
ASTM D3826-98(2013)..
ASTM D3835-08
ASTM D3895-07
ASTM D3935-09
ASTM D4094-07
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D4066-13
Standard Classification System for Nylon Injection and Extrusion Materials (PA)
Automaticky preložený názov:
Štandardný systém klasifikácie Nylon vstrekovanie a vytlačovanie materiálov (PA)
NORMA vydaná dňa 1.7.2013
Informácie o norme:
Označenie normy: ASTM D4066-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2013
Kód tovaru: NS-25916
Počet strán: 18
Približná hmotnosť: 54 g (0.12 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D4066-13 :
Keywords:
classification, classification system, line callout, plastic materials, ICS Number Code 83.080.20 (Thermoplastic materials)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This classification system covers nylon materials suitable for injection molding and extrusion. Some of these compositions are also suitable for compression molding and application from solution. 1.2 The properties included in this classification system are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These may be specified by using the suffixes as given in Section 1.3 This classification system and subsequent line call-out (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
|
|
Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
|
|
Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023).
|
|
Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
|
|
Standard Terminology Relating to Plastics
|
|
Standard Test Method for Tensile Properties of Plastics
|
|
Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
|
|
Standard Test Method for Determination of Relative Viscosity of Concentrated Polyamide (PA) Solutions
|
|
Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
|
|
Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
|
|
Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023).
|
|
Standard Test Methods for DC Resistance or Conductance of Insulating Materials (Includes all amendments and changes 5/6/2021).
|
|
Standard Practice for Conditioning Plastics for Testing
|
|
Standard Test Method for Tensile Properties of Plastics
|
|
Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
|
|
Standard Test Method for Determination of Relative Viscosity of Concentrated Polyamide (PA) Solutions
|
|
Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
|
|
Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
|
|
Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
|
VV-I-530
|
Insulating Oil, Electrical (for Transformers, Switches, and Circuit Breakers)
|
|
Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
|
|
Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
|
|
Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
|
|
Standard Practice for Packaging/Packing of Plastics
|
|
Standard Classification System for Specifying Plastic Materials
|
|
Standard Test Method for Ash Content in Plastics
|
|
Standard Test Method for Gravimetric Determination of Carbon Black in Nylon Materials (PA) (Withdrawn 2004)
|
|
Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
|
L-P-410
|
Plastic, Polyamide (Nylon) Rigid: Rods, Tubes, Flats, Molded and Cast Parts |
Podobné normy:
Historická
1.11.2013
Historická
1.2.2013
Historická
1.12.2008
Historická
1.4.2007
Historická
15.4.2009
Historická
1.11.2007
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
