Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts
Automaticky preložený názov:
Štandard Specification k Contact tvarovaný a ldquo; sklenených vlákien a rdquo; (Glass Fiber Reinforced Teplom Resin) kanály
NORMA vydaná dňa 1.3.2014
Označenie normy: ASTM D3982-08(2014)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2014
Kód tovaru: NS-25594
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
chemical resistance, contact molding, ducts, flanges, polyester resin, reinforced plastic, ICS Number Code 83.120 (Reinforced plastics)
1. Scope | ||||||||||||||||
1.1 This specification covers ducts fabricated by contact molding intended for use in handling corrosive fumes and process gases. Special attention is given to equipment that operates at temperatures over 180°F (82.2°C) with regard to strength and corrosion resistance. 1.2 The material of construction shall be “fiberglass” consisting of a polyester, vinyl ester, or other qualified resin-matrix systems with fiber reinforcement in accordance with Specification C582. 1.3 This specification is not intended to cover selection of resins and reinforcements for specific chemical environments. 1.4 This specification covers ducts up to a design pressure of ±5 psig (34.5 Pa). 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment
|
|
Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
|
|
Standard Terminology Relating to Plastics
|
|
Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
|
|
Standard Test Method for Ignition Loss of Cured Reinforced Resins
|
|
Standard Terminology Relating to Plastic Piping Systems
|
NFPA?91
|
Installation of Blower and Exhaust Systems for Duct, Stack and Vapor Removal or Conveying Available from National Fire Protection Association (NFPA), 1 Batterymarch Park, Quincy, MA 02169-7471, http://www.nfpa.org.
|
|
Standard Specification for Hardened Steel Washers |
Historická
15.12.2007
Historická
1.4.2012
Historická
1.4.2012
Historická
1.4.2007
Historická
1.4.2007
Historická
1.9.2009
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.