ASTM D2152-13
ASTM D2444-99(2010)..
ASTM D2466-13
ASTM D2467-13a
ASTM D2513-14e1
ASTM D2517-06(2011)..
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D3840-14
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications
Automaticky preložený názov:
Štandardné špecifikácie pre a ldquo; sklenených vlákien a rdquo; (Sklenými vláknami vystužený Teplom-živice) armatúra pre Nonpressure aplikácie
NORMA vydaná dňa 1.4.2014
Informácie o norme:
Označenie normy: ASTM D3840-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2014
Kód tovaru: NS-25057
Počet strán: 9
Približná hmotnosť: 27 g (0.06 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D3840-14 :
Keywords:
dimensions, fabrication, fiberglass, fittings, overlays, pipe, ICS Number Code 23.040.45 (Plastic fittings)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||
|
1.1 This specification covers fiberglass pipe fittings intended for use in gravity flow systems for conveying sanitary sewage, storm water, and those industrial wastes for which the fittings are determined to be suitable. Elbows, tees, laterals, crosses, reducers, and adapters are included. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipes. 1.2 This specification is intended
to cover only dimensions, material properties, and workmanship
rather than the structural design of the fittings. The structural
design of the fittings shall be as agreed upon between purchaser
and supplier, and needs to take into consideration the anticipated
conditions of installation and service.
1.3 This specification covers only fittings fabricated from cut sections of pipe, or from a combination of pipe sections and contact molded (hand layup), or machine fabricated components. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Practice for Packaging/Packing of Plastics
|
|
Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
|
|
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe
|
|
Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe (Includes all amendments and changes 9/12/2019).
|
|
Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
|
Standard Terminology Relating to Plastics
|
|
Standard Test Method for Tensile Properties of Plastics
|
|
Standard Terminology Relating to Plastic Piping Systems
|
|
Standard Specification for Epoxy Resins
|
|
Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
Podobné normy:
Historická
1.5.2013
Historická
1.8.2010
Historická
1.8.2013
Historická
1.8.2013
Historická
25.4.2014
Historická
15.11.2011
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
