ASTM D3839-14
ASTM D3915-06
ASTM D3965-11
ASTM D4396-06
ASTM D5365-12
ASTM D5677-05(2010)..
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D3754-14
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
Automaticky preložený názov:
Štandardné špecifikácie pre a ldquo; sklenených vlákien a rdquo; (Sklenými vláknami vystužený Teplom-živice), kanalizácie a priemyselné tlakové potrubie
NORMA vydaná dňa 1.3.2014
Informácie o norme:
Označenie normy: ASTM D3754-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2014
Kód tovaru: NS-24734
Počet strán: 14
Približná hmotnosť: 42 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D3754-14 :
Keywords:
fiberglass pipe, sewer pipe, industrial pipe, pressure pipe, strain corrosion, hydrostatic design basis, ICS Number Code 23.040.20 (Plastic pipes)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 156 in. (4000 mm), for use in pressure systems for conveying sanitary sewage, storm water, and many industrial wastes, and corrosive fluids. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipes. This standard is suited primarily for pipes to be installed in buried applications, although it may be used to the extent applicable for other installations such as, but not limited to, jacking, tunnel lining and slip-lining and rehabilitation of existing pipelines. Pipe covered by this specification is intended to operate at internal gage pressures of 450 psi (3103 kPa) or less. 1.2 The values given in inch-pound
units are to be regarded as the standard. The values given in
parentheses are provided for information purposes only.
1.3 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
|
|
Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
|
|
Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
|
|
Standard Terminology Relating to Plastics
|
|
Standard Specification for Concrete Aggregates
|
|
Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
|
|
Standard Test Method for Tensile Properties of Plastics
|
|
Standard Test Method for Compressive Properties of Rigid Plastics
|
|
Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
ISO?1172
|
Textile Glass Reinforced Plastics--Determination of Loss on Ignition Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
|
AWWA C-950
|
Glass-Fiber Reinforced Thermosetting Resin Pressure Pipe Available from American Water Works Association (AWWA), 6666 W. Quincy Ave., Denver, CO 80235, http://www.awwa.org.
|
|
Standard Terminology Relating to Plastic Piping Systems
|
|
Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
|
|
Standard Practice for Packaging/Packing of Plastics
|
|
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
|
|
Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
|
|
Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe (Includes all amendments and changes 9/12/2019).
|
|
Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
|
|
Standard Test Method for Ignition Loss of Cured Reinforced Resins |
Podobné normy:
Historická
1.3.2014
Historická
1.12.2006
Historická
1.9.2011
Historická
1.12.2006
Historická
1.4.2012
Historická
1.11.2010
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
