Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D3517-14

Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe

Automaticky preložený názov:

Štandardné špecifikácie pre a ldquo; sklenených vlákien a rdquo; (Sklenými vláknami vystužený Teplom-živice) výtlačného potrubia

NORMA vydaná dňa 1.3.2014

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 77.60 € Tlačené - 77.60 €
Dostupnosť	SKLADOM
Cena	77.60 € bez DPH
77.60 €

Informácie o norme:

Označenie normy: ASTM D3517-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2014
Kód tovaru: NS-23924
Počet strán: 13
Približná hmotnosť: 39 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty

Anotácia textu normy ASTM D3517-14 :

Keywords:
fiberglass pipe, hydrostatic design basis, pressure pipe, RPMP, RTRP, ICS Number Code 23.040.20 (Plastic pipes)

Doplňujúce informácie

1. Scope

1.1 This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 156 in. (4000 mm), intended for use in water conveyance systems which operate at internal gage pressures of 450 psi (3103 kPa) or less. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipes. The standard is suited primarily for pipes to be installed in buried applications, although it may be used to the extent applicable for other installations such as, but not limited to, jacking, tunnel lining and slip-lining rehabilitation of existing pipelines.

1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

1.3 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D2290-19a	Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe (Includes all amendments and changes 9/12/2019).
C33-07	Standard Specification for Concrete Aggregates
ISO?1172	Textile Glass Reinforced Plastics--Determination of Loss on Ignition Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Standard No. 61	Drinking Water System Components Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F412-23	Standard Terminology Relating to Plastic Piping Systems
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D4161-14(2019)	Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
D695-23	Standard Test Method for Compressive Properties of Rigid Plastics
D638-22	Standard Test Method for Tensile Properties of Plastics
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D883-24	Standard Terminology Relating to Plastics
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2584-18	Standard Test Method for Ignition Loss of Cured Reinforced Resins
D2992-22	Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
D3567-17(2022)	Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings