Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Rubber Deterioration—Discoloration from Ultraviolet (UV) or UV/Visible Radiation and Heat Exposure of Light-Colored Surfaces
Automaticky preložený názov:
Štandardná skúšobná metóda pre Rubber skazeného & ndash; Zafarbenie z Ultrafialové žiarenie (UV) alebo UV / viditeľné žiarenie a tepla Expozícia svetlé podlahy
NORMA vydaná dňa 1.1.2013
Označenie normy: ASTM D1148-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.2013
Kód tovaru: NS-16459
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
fluorescent UV, heat discoloration, rubber products, ultraviolet, ultraviolet light discoloration, UVA-340, xenon arc, ICS Number Code 83.060 (Rubber)
Significance and Use | ||||||||||||||
4.1 The surface of white or light-colored vulcanized rubber articles, or vulcanized rubber covered with an organic finish, may discolor when exposed to conditions of humidity, or moisture, heat, and sunlight. This change in color of light-colored rubber surfaces is objectionable to the consumer. 4.2 Results obtained should be treated only as indicating the effect of irradiance from the specified source (either UVA-340 lamps or a xenon arc with a Daylight Filter) and not as equivalent to the result of any natural exposure, unless the degree of quantitative correlation has been empirically established for the material in question. 4.3 This test method may be used for producer-consumer acceptance, referee purposes, and research and development work. |
||||||||||||||
1. Scope | ||||||||||||||
1.1 This test method covers techniques to evaluate the surface discoloration of white or light-colored vulcanized rubber that may occur when subjected to UV or UV/visible exposure from specified sources under controlled conditions of relative humidity, or moisture, and temperature. 1.2 This test method also describes how to qualitatively evaluate the degree of discoloration produced under such conditions. 1.3 The term “discoloration” applies to a color change of the rubber sample, as distinguished from staining (see Note 1), that refers to a color change of a metal finish in contact with or adjacent to the rubber specimen. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
|
|
Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
|
|
Standard Test Methods for Rubber Property´Staining of Surfaces (Contact, Migration, and Diffusion)
|
|
Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets (Includes all amendments and changes 11/12/2021).
|
|
Standard Practice for Rubber´Preparation of Pieces for Test Purposes from Products
|
|
Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials
|
|
Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials |
Historická
1.11.2011
Historická
1.5.2012
Historická
1.5.2012
Historická
1.11.2011
Historická
1.8.2012
Historická
1.12.2010
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.