Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Rubber—Identification by Pyrolysis-Gas Chromatography
Automaticky preložený názov:
Štandardná prax pre Guma & ndash; Identifikácia pyrolýzou-plynovej chromatografie
NORMA vydaná dňa 1.8.2012
Označenie normy: ASTM D3452-06(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2012
Kód tovaru: NS-23679
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
GC, gas chromatography, pyrogram, pyrolysis, rubber composition, rubber identification, ICS Number Code 83.060 (Rubber)
Significance and Use | ||||||
3.1 For research, development, and quality control purposes, it is advantageous to determine the composition of rubbers in cured, compounded products. 3.2 This practice provides such composition analysis, utilizing a gas chromatograph and pyrolysis products from rubber decomposition. |
||||||
1. Scope | ||||||
1.1 This practice covers the identification of polymers in raw rubbers, and cured and uncured compounds, based on a single polymer, by the gas chromatographic patterns of their pyrolysis products (pyrograms). Implementation of this guide presupposes a working knowledge of the principles and techniques of gas chromatography, sufficient to carry out this practice and to interpret the results correctly.2 1.2 This practice will identify the following polymers: 1.2.1 Polyisoprene of natural or synthetic origin, 1.2.2 Butadiene-styrene copolymers, 1.2.3 Polybutadiene, 1.2.4 Polychloroprene, 1.2.5 Butadiene-acrylonitrile copolymers, 1.2.6 Ethylene-propylene copolymers and related terpolymers, and 1.2.7 Isobutene-isoprene copolymers. 1.3 This practice will not differentiate the following polymers: 1.3.1 Natural polyisoprene from synthetic polyisoprene. 1.3.2 Butadiene-styrene copolymers produced by solution and emulsion polymerization. It is sometimes possible to distinguish butadiene-styrene copolymers containing different amounts of styrene as well as random polymers from block polymers. 1.3.3 Polybutadiene with different microstructures. 1.3.4 Different types of polychloroprenes. 1.3.5 Butadiene-acrylonitrile copolymers with different monomer ratios. 1.3.6 Ethylene-propylene copolymers with different monomer ratios, as well as the copolymers from the related terpolymers. 1.3.7 Isobutene-isoprene copolymers (butyl rubbers) from halogenated butyl rubbers. 1.3.8 Polyisoprene containing different amounts of cis-trans isomers. 1.3.9 The practice does not identify ebonite or hard rubbers. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
2. Referenced Documents | ||||||
|
Historická
1.12.2011
Historická
1.5.2010
Historická
1.5.2010
Historická
1.5.2014
Historická
1.12.2012
Historická
1.3.2014
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.