Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C1533-15

Standard Guide for General Design Considerations for Hot Cell Equipment

Automaticky preložený názov:

Štandardné príručka pre General dizajn úvahy pre horúce komory zariadenia

NORMA vydaná dňa 1.1.2015

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 77.00 € Tlačené - 77.00 €
Dostupnosť	SKLADOM
Cena	77.00 € bez DPH
77.00 €

Informácie o norme:

Označenie normy: ASTM C1533-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.2015
Kód tovaru: NS-579674
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Technika jaderných reaktorů

Anotácia textu normy ASTM C1533-15 :

Keywords:
design, equipment, hot cell, manipulator, remote,, ICS Number Code 27.120.10 (Reactor engineering)

Doplňujúce informácie

Significance and Use

4.1 The purpose of this guide is to provide general guidelines for the design and operation of hot cell equipment to ensure longevity and reliability throughout the period of service.

4.2 It is intended that this guide record the general conditions and practices that experience has shown is necessary to minimize equipment failures and maximize the effectiveness and utility of hot cell equipment. It is also intended to alert designers to those features that are highly desirable for the selection of equipment that has proven reliable in high radiation environments.

4.3 This guide is intended as a supplement to other standards, and to federal and state regulations, codes, and criteria applicable to the design of equipment intended for hot cell use.

4.4 This guide is intended to be generic and to apply to a wide range of types and configurations of hot cell equipment.

1. Scope

1.1 Intent:

1.1.1 The intent of this guide is to provide general design and operating considerations for the safe and dependable operation of remotely operated hot cell equipment. Hot cell equipment is hardware used to handle, process, or analyze nuclear or radioactive material in a shielded room. The equipment is placed behind radiation shield walls and cannot be directly accessed by the operators or by maintenance personnel because of the radiation exposure hazards. Therefore, the equipment is operated remotely, either with or without the aid of viewing.

1.1.2 This guide may apply to equipment in other radioactive remotely operated facilities such as suited entry repair areas, canyons or caves, but does not apply to equipment used in commercial power reactors.

1.1.3 This guide does not apply to equipment used in gloveboxes.

1.2 Applicability:

1.2.1 This guide is intended for persons who are tasked with the planning, design, procurement, fabrication, installation, or testing of equipment used in remote hot cell environments.

1.2.2 The equipment will generally be used over a long-term life cycle (for example, in excess of two years), but equipment intended for use over a shorter life cycle is not excluded.

1.2.3 The system of units employed in this standard is the metric unit, also known as SI Units, which are commonly used for International Systems, and defined by IEEE/ASTM SI 10: American National Standard for Use of the International System of Units (SI): The Modern Metric System.

1.3 Caveats:

1.3.1 This guide does not address considerations relating to the design, construction, operation, or safety of hot cells, caves, canyons, or other similar remote facilities. This guide deals only with equipment intended for use in hot cells.

1.3.2 Specific design and operating considerations are found in other ASTM documents.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents

F593-22	Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
IEEE/ASTM SI 10	American National Standard for Use of the International System of Units (SI): The Modern Metric System
A490-14	Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
C859-24	Standard Terminology Relating to Nuclear Materials
C1217-00(2020)	Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials
C1572-10	Standard Guide for Dry Lead Glass and Oil-Filled Lead Glass Radiation Shielding Window Components for Remotely Operated Facilities
C1615-10	Standard Guide for Mechanical Drive Systems for Remote Operation in Hot Cell Facilities
C1661-23	Standard Guide for Viewing Systems for Remotely Operated Facilities
A276-13	Standard Specification for Stainless Steel Bars and Shapes
A320/A320M-22a	Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service (Includes all amendments and changes 11/23/2022).
A354-17e2	Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners (Includes all amendments and changes 11/27/2018).
A479/A479M-23a	Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels (Includes all amendments and changes 6/9/2023).
A193/A193M-23	Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications
A240/A240M-23a	Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications (Includes all amendments and changes 11/7/2023).
A489-18e1	Standard Specification for Carbon Steel Eyebolts (Includes all amendments and changes 5/17/2018).
C1725-17(2022)	Standard Guide for Hot Cell Specialized Support Equipment and Tools
D676-59	Method of Test for Indentation of Rubber by Means of a Durometer (Withdrawn 1964)
D5144-08(2021)	Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants