Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Green Strength of Specimens Compacted from Metal Powders
Automaticky preložený názov:
Štandardná skúšobná metóda pre Green Pevnosť vzoriek zhutnené z kovových práškov
NORMA vydaná dňa 1.6.2014
Označenie normy: ASTM B312-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2014
Kód tovaru: NS-6193
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
constant loading beam device, green strength, PM, powder metallurgy, transverse strength, unsintered compact, ICS Number Code 77.160 (Powder metallurgy)
Significance and Use | ||||||||||||
5.1 The green strength value determined under the conditions specified by this test method is influenced by the characteristics of the powder, how it compacts under the specified conditions (i.e., the particle to particle bonding that exists following compacting), and the lubrication system used. 5.2 Knowledge of the green strength value is useful to the production, characterization and utilization of metal powders in the manufacture of PM structural parts and bearings. 5.3 The test for green strength of a compacted metal powder can be used to: 5.3.1 Relate the resistance of a pressed compact to breakage or damage due to handling. 5.3.2 Compare the quality of a metal powder or powder mixture from lot to lot. 5.3.3 Determine the effect of the addition of a lubricant or other powders to a base powder. 5.3.4 Evaluate powder mixing or blending variables. 5.4 Factors that are known to influence the green strength of a metal powder are particle shape, particle size distribution and compressibility of the metal powder. 5.5 The amount and type of lubricant or other additives and the mixing procedures have a strong effect on the green strength of specimens produced from metal powder mixtures. |
||||||||||||
1. Scope | ||||||||||||
1.1 This standard covers a test method that may be used to measure the transverse rupture strength of a compacted but unsintered (green) test specimen produced from lubricated or unlubricated metal powders or powder mixtures. 1.2 Green strength is measured by a quantitative laboratory procedure in which the fracture strength is calculated from the force required to break an unsintered test specimen supported as a simple beam while subjected to a uniformly increasing three-point transverse load under controlled conditions. 1.3 This test method is a companion standard to Test Method B528 that covers the measurement of the transverse rupture strength of sintered PM test specimens. 1.4 With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimeter (g/cm3) and gram (g) units is the longstanding industry practice, the values in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||
2. Referenced Documents | ||||||||||||
|
Historická
1.9.2014
Historická
1.9.2014
Historická
1.4.2009
Historická
1.4.2013
Historická
1.6.2013
Historická
1.10.2008
Posledná aktualizácia: 2024-12-23 (Počet položiek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.