Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Carbon and Alloy Steel Nuts (Metric) (Withdrawn 2021)
Automaticky preložený názov:
Štandard Specification pre Carbon a legovanej ocele orechy (metrické)
NORMA vydaná dňa 1.11.2013
Označenie normy: ASTM A563M-07(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2013
Kód tovaru: NS-3115
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
alloy steel, carbon steel, metric, nuts, steel, weathering steel, ICS Number Code 21.060.20 (Nuts)
1. Scope | ||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers chemical and mechanical requirements for eight property classes of hex and hex-flange carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts. 1.2 Classes 8S3 and 10S3 nuts have
atmospheric corrosion resistance and weathering characteristics
comparable to those of the steels covered in Specification
A588/A588M. The atmospheric corrosion resistance of these steels is
substantially better than that of carbon steel with or without
copper addition (see 1.3 The nut size range for which
each class is applicable is given in the table on mechanical
requirements.
1.4 Appendix X1 gives guidance to assist designers and purchasers in the selection of a suitable class. 1.5 Appendix X2 gives data on the properties of slotted hex nuts and hex jam nuts. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
|
B?18.2.4.4M
|
Metric Hex Flange Nuts
|
B?18.2.4.3M
|
Metric Slotted Hex Nuts
|
B?18.2.4.6M
|
Metric Heavy Hex Nuts
|
|
Standard Test Methods and Practices for Chemical Analysis of Steel Products
|
|
Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
|
|
Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric) (Withdrawn 2016)
|
|
Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare
|
|
Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)
|
|
Standard Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance
|
B?18.2.4.5M
|
Metric Hex Jam Nuts
|
B?18.2.4.2M
|
Metric Hex Nuts, Style 2
|
B?18.2.4.1M
|
Metric Hex Nuts, Style 1
|
B?1.13M
|
Metric Screw Threads--M Profile
|
|
Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
|
|
Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series
|
|
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric) (Withdrawn 2015)
|
|
Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Withdrawn 2012)
|
|
Standard Practice for Commercial Packaging
|
|
Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
|
|
Standard Terminology for F16 Mechanical Fasteners |
Historická
1.4.2014
Historická
15.5.2011
Historická
1.4.2013
Historická
1.4.2012
Historická
1.11.2009
Historická
1.10.2007
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-04 (Počet položiek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.