Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ISO 16063-31:2009
Methods for the calibration of vibration and shock transducers — Part 31: Testing of transverse vibration sensitivity
Automaticky preložený názov:
Metódy kalibrácie snímačov vibrácií a rázov - Časť 31: Skúšanie priečnej citlivosti vibrácií
NORMA vydaná dňa 11.8.2009
Informácie o norme:
Označenie normy: ISO 16063-31:2009
Dátum vydania normy: 11.8.2009
Kód tovaru: NS-426847
Počet strán: 18
Približná hmotnosť: 54 g (0.12 libier)
Krajina: Medzinárodná technická norma
Kategória: Technické normy ISO
Kategórie - podobné normy:
Anotácia textu normy ISO 16063-31:2009 :
Description / Abstract: ISO 16063-31:2009 specifies details of the instrumentation and methods to be used for transverse vibration sensitivity testing. It applies to rectilinear velocity and acceleration transducers. The methods and procedures specified in ISO 16063-31:2009 allow the determination of the sensitivity of a transducer to vibration in the plane perpendicular to its geometric axis of sensitivity. Because the magnitude of this transverse sensitivity can vary with the direction of the applied vibration, the various methods determine the maximum value. Using that value, the ratio of the transverse sensitivity to the sensitivity on the geometric axis of the transducer can be calculated. In addition, the angle at which the maximum transverse sensitivity occurs can be determined. The methods and techniques specified can be applied without re-mounting the transducer away from its mounting surface during the test, thus avoiding significant uncertainties often encountered in methods which require repeated mounting. The different methods specified use a single-axis vibration exciter, a two-axis vibration exciter or a tri-axial vibration exciter. Tri-axial vibration excitation allows the transverse sensitivity and the sensitivity on the geometric axis to be determined simultaneously, thus simulating application conditions where the transducer is exposed to multi-axial vibration. ISO 16063-31:2009 is applicable to a frequency range from 1 Hz to 5 kHz and for a dynamic range from 1 m/s2 to 1 000 m/s2 (frequency dependent) and from 1 mm/s to 1 m/s (frequency dependent). Although among all the systems specified it is possible to achieve these ranges, generally each has limitations permitting its use in much smaller ranges. The methods specified are by comparison both to a reference transducer and to a laser interferometer. The methods specified allow an expanded uncertainty of the transverse sensitivity (coverage factor k = 2) of 0,1 % or less to be achieved, if the expanded uncertainty is expressed as a percentage of the sensitivity of the test transducer in its sensitive axis.
K tejto norme patria tieto zmeny:
ISO 16063-31:2009/Amd1:2025
Zmena
Zobraziť všetky technické informácie
Methods for the calibration of vibration and shock transducers — Part 31: Testing of transverse vibration sensitivity — Amendment 1
(Méthodes pour l´étalonnage des transducteurs de vibrations et de chocs — Partie 31: Essai de sensibilité aux vibrations transversales — Amendement 1)
Zmena vydaná dňa 5.3.2025
Vybraný formát:Zobraziť všetky technické informácie
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
