Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test
Automaticky preložený názov:
Štandardná skúšobná metóda pre umiestnenie odolnosti materiálov pre posuvné Oblečenie Použitie Block-on-Ring Wear test
NORMA vydaná dňa 1.4.2010
Označenie normy: ASTM G77-05(2010)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2010
Kód tovaru: NS-57819
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
block-on-ring, metal, sliding, wear, wear test, Block-on-ring wear test, Coefficient of friction (COF), Deformation, Loading tests--metals/alloys, Metals and metallic materials, Polymers, Sliding wear test data, Steel, Surface analysis--metals/alloys, Volume change, Wear testing--metallic materials, Wear testing--textiles, Weight, ICS Number Code 77.040.10 (Mechanical testing of metals)
Significance and Use | ||||||||||
The significance of this test method in any overall measurement program directed toward a service application will depend on the relative match of test conditions to the conditions of the service application. This test method seeks only to prescribe the general test procedure and method of calculating and reporting data. The choice of test operating parameters is left to the user. A fixed amount of sliding distance must be used because wear is usually non-linear with distance in this test. |
||||||||||
1. Scope | ||||||||||
1.1 This test method covers laboratory procedures for determining the resistance of materials to sliding wear. The test utilizes a block-on-ring friction and wear testing machine to rank pairs of materials according to their sliding wear characteristics under various conditions. 1.2 An important attribute of this test is that it is very flexible. Any material that can be fabricated into, or applied to, blocks and rings can be tested. Thus, the potential materials combinations are endless. However, the interlaboratory testing has been limited to metals. In addition, the test can be run with various lubricants, liquids, or gaseous atmospheres, as desired, to simulate service conditions. Rotational speed and load can also be varied to better correspond to service requirements. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Wear test results are reported as the volume loss in cubic millimetres for both the block and ring. Materials of higher wear resistance will have lower volume loss. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||
2. Referenced Documents | ||||||||||
|
Historická
1.10.2011
Historická
1.11.2010
Historická
1.11.2010
Historická
1.9.2008
Historická
1.6.2012
Historická
1.1.2000
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.