Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F959M-13

Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use With Structural Fasteners (Metric) (Withdrawn 2016)

Automaticky preložený názov:

Štandard Specification pre kompresiu-podložka-Type Priame napínacie indikátory pre použitie na štrukturálne Spojovací materiál (metrické)

NORMA vydaná dňa 1.3.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 68.60 € Tlačené - 68.60 €
Dostupnosť	SKLADOM
Cena	68.60 € bez DPH
68.60 €

Informácie o norme:

Označenie normy: ASTM F959M-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2013
Kód tovaru: NS-57084
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Podložky, zajišťovací součásti

Anotácia textu normy ASTM F959M-13 :

Keywords:
compressible-washer-type, direct tension indicators, DTI, indicators, ICS Number Code 21.060.30 (Washers, locking elements)

Doplňujúce informácie


1. Scope
1.1 This specification covers the requirements for compressible-washer-type direct tension indicators capable of indicating the achievement of a specified minimum bolt tension in a structural bolt. 1.2 Two types of direct tension indicators in nominal diameter sizes M16 through M36 are covered: 1.2.1 Type 8.8—direct tension indicators for use with Specification A325M bolts, and 1.2.2 Type 10.9—direct tension indicators for use with Specification A490M bolts. 1.3 Direct tension indicators are intended for installation under either a bolt head or a hardened washer. (See Research Council on Structural Connections: Specification for Structural Joints Using ASTM A325 or A490 Bolts.) 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 The following precautionary statement pertains only to the test methods portions, Section 12, and Appendix X1 of this specification:
A490M-14	Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)
B695-21	Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
D3951-18(2023)	Standard Practice for Commercial Packaging
F606M-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric) (Withdrawn 2015)
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
Specification for Structural Joints Using ASTM A? 325 or Bolts	Available from Research Council on Structural Connections at www.boltcouncil.org.
A325M-14	Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric) (Withdrawn 2016)
F436M-11	Standard Specification for Hardened Steel Washers [Metric] (Withdrawn 2016)