Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F876-03e1 10.5.2003 náhľad

Doplňujúce informácie

ASTM F876-03e1

Standard Specification for Crosslinked Polyethylene (PEX) Tubing (Includes all amendments And changes 8/16/2017).

Automaticky preložený názov:

Štandardné špecifikácie pre zosietený polyetylén ( PEX ) Tubing

NORMA vydaná dňa 10.5.2003

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 71.20 € Tlačené - 71.20 €
Dostupnosť	SKLADOM
Cena	71.20 € bez DPH
71.20 €

Informácie o norme:

Označenie normy: ASTM F876-03e1
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.5.2003
Kód tovaru: NS-56748
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F876-03e1 :

Keywords:

crosslinked polyethylene, hydrostatic stress, PEX, PPI, pipe, pressure, tubing

Doplňujúce informácie

1. Scope

1.1 This specification covers crosslinked polyethylene (PEX) tubing that is outside diameter controlled, made in standard thermoplastic tubing dimension ratios, and pressure rated for water at three temperatures (see Appendix X1). Included are requirements and test methods for material, workmanship, dimensions, sustained pressure, burst pressure, environmental stress cracking, stabilizer migration resistance, and degree of crosslinking. Methods of marking are also given.

1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D1898-68(1989)	Standard Practice for Sampling of Plastics (Withdrawn 1998)
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D618-21	Standard Practice for Conditioning Plastics for Testing
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D2837-22	Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
D3895-19	Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
F412-23	Standard Terminology Relating to Plastic Piping Systems
F1281-24	Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe
D2765-16(2024)	Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
F2023-21	Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Pipe, Tubing and Systems to Hot Chlorinated Water
F2657-21	Standard Test Method for Outdoor Weathering Exposure of Crosslinked Polyethylene (PEX) Tubing
	Standards Dimensions of Steel Pipe (IPS) Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
MIL-STD-129	Marking for Shipment and Storage
NSF/ANSI 14
ISO 1167	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids -- Determination of the resistance to internal pressure -- Part 1: General method
ISO 13760	Plastics pipes for the conveyance of fluids under pressure -- Miners rule -- Calculation method for cumulative damage

PPI TR-4	PPI Listing of Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB) and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe
D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.