Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F810-12

Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields

Automaticky preložený názov:

Štandard Specification pre SmoothWall polyetylénu (PE) rúry pre použitie v odvodnenie a odpadov Absorpcia Fields

NORMA vydaná dňa 1.11.2012

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 67.10 € Tlačené - 67.10 €
Dostupnosť	SKLADOM
Cena	67.10 € bez DPH
67.10 €

Informácie o norme:

Označenie normy: ASTM F810-12
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2012
Kód tovaru: NS-56514
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty

Anotácia textu normy ASTM F810-12 :

Keywords:

drain pipe, fittings, perforated pipe, pipe, polyethylene, under-drain, ICS Number Code 23.040.20 (Plastic pipes)

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements and test methods for workmanship, flattening, dimensions, tolerances, stiffness, perforations, environmental stress cracking, bonding, and impact resistance for smoothwall perforated and nonperforated polyethylene (PE) pipe, including coextruded and closed profile pipe. Methods of marking are also included.

1.2 This specification includes two stiffness classes, referred to as, “Standard” and “Heavy Duty.”

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.

1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D1693-21	Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
D2852-16	Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings (Withdrawn 2022)
D2751-05	Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014)
D2729-21	Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D3034-23	Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
F412-23	Standard Terminology Relating to Plastic Piping Systems
F481-97(2019)	Standard Practice for Installation of Thermoplastic Pipe and Corrugated Pipe in Septic Tank Leach Fields
Fed. Std. No. 123	Marking for Shipments (Civil Agencies) Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
MIL-STD-129	Marking for Shipment and Storage
D3033-85	Specification for Type PSP Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings (Withdrawn 1987)
D618-21	Standard Practice for Conditioning Plastics for Testing
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)