Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F794-03

Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter

Automaticky preložený názov:

Štandardné špecifikácie pre poly ( vinyl chloridu ) ( PVC ) Profile Gravity kanalizačné rúry a tvarovky na základe Kontrolovaná Vnútorný priemer

NORMA vydaná dňa 1.10.2003

Jazyk
Prevedenie	Online zabezpečené PDF - 72.60 € Tlačené - 72.60 €
Dostupnosť	SKLADOM
Cena	72.60 € bez DPH
72.60 €

Informácie o norme:

Označenie normy: ASTM F794-03
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2003
Kód tovaru: NS-56472
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F794-03 :

Keywords:

profile wall, PVC, sewer pipe, ICS Number Code 23.040.20 (Plastic pipes), 23.040.45 (Plastic fittings)

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements for poly(vinyl chloride) (PVC) profile sewer pipe and fittings with integral bell and elastomeric seal joints or plain end pipe with couplings in sizes (4 to 48 in.) based on a controlled inside diameter.

1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 The following safety hazard caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1—Pipe and fittings produced to this specification should be installed in accordance with Practice D 2321.

2. Referenced Documents

AWWA Manual M45	Fiberglass Pipe Design Available from American Water Works Association (AWWA), 6666 W. Quincy Ave., Denver, CO 80235, http://www.awwa.org.
Fed. Std. No. 123	Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.
MIL-STD-129	Marking for Shipment and Storage
D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
F402-18	Standard Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D3212-21	Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D2855-20	Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
D3034-23	Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D618-21	Standard Practice for Conditioning Plastics for Testing
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1784-20	Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2152-23	Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion
F412-23	Standard Terminology Relating to Plastic Piping Systems
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F679-21	Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.