Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F771-99

Standard Specification for Polyethylene (PE) Thermoplastic High-Pressure Irrigation Pipeline Systems

Automaticky preložený názov:

Štandardné špecifikácie pre polyetylén ( PE ) Termoplastický vysokotlakové Zavlažovacie Potrubné systémy

NORMA vydaná dňa 10.4.1999

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 79.90 € Tlačené - 79.90 €
Dostupnosť	SKLADOM
Cena	79.90 € bez DPH
79.90 €

Informácie o norme:

Označenie normy: ASTM F771-99
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.4.1999
Kód tovaru: NS-56399
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F771-99 :

Keywords:

Irrigation piping, Land drainage piping systems, polyethylene (PE) thermoplastic high-pressure irrigation pipeline, systems-classifying materials/identifying requirements, spec.,, Polyethylene (PE) pipe, high-pressure irrigation pipeline systems-classifying, materials/identifying requirements, spec.,,Order Form, ICS Number Code 23.040.20 (Plastic pipes)

Doplňujúce informácie

1. Scope

1.1 This specification covers polyethylene (PE) thermoplastic pipelines used to convey, at rated pressures of 80 to 200 psi, water that is to be used for irrigation purposes. This specification includes criteria for classifying the pipe materials, a system of nomenclature for plastic pipe, requirements for pipe, test methods, joints, fittings, certification, and marking.

1.2 The values stated in inch-pound units are to be regarded as the standard.

1.3 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

Fed. Std. No. 123	Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
MIL-STD-129	Marking for Shipment and Storage
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique
D1248-16	Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
D2609-21	Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
D2683-20	Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
D2837-22	Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
D3035-22	Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
D3261-24	Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
F412-23	Standard Terminology Relating to Plastic Piping Systems
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2239-22	Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.