Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter (Includes all amendments And changes 5/10/2022).
NORMA vydaná dňa 1.5.2021
Označenie normy: ASTM F714-21a
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2021
Kód tovaru: NS-1024092
Počet strán: 12
Približná hmotnosť: 36 g (0.08 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
industrial pipe, non-pressure pipe, plastic pipe, polyethylene pipe, pressure pipe, sewer pipe, water pipe,, ICS Number Code 23.040.20 (Plastic pipes)
1. Scope | ||||||||||||||||||||||||||
1.1?This specification covers polyethylene (PE) pipe made in three standard outside diameter sizing systems, based on outside diameters of DIPS 3, IPS 4, Metric 90 mm and larger. For smaller sizes refer to Specification D3035. See 5.2.5 for guidelines on special sizes. 1.2?The piping is intended for new construction and insertion renewal of old piping systems used for the transport of water, municipal sewage, domestic sewage, industrial process liquids, effluents, slurries, etc., in both pressure and nonpressure systems. Note 1:?The user should consult the manufacturer to ensure
that any mechanical or chemical effects to the polyethylene pipe
caused by the material being transported will not affect the
service life beyond limits acceptable to the user. See PPI TR-19
Chemical Resistance of Thermoplastic Piping Materials for guidance
on chemical effects, www.plasticpipe.org
1.3?All pipes produced under this specification are pressure-rated. See Appendix X5 for information on pressure rating. Note 2:?References and material descriptions for PE2406,
PE3408 and materials having a HDB of 1450 psi have been removed
from Specification F714 due
to changes in Specification D3350 and PPI TR-3. For removed
designations, refer to previous editions of Specification
F714, Specification
D3350, PPI TR-3 and PPI TR-4.
The removal of these materials does not affect pipelines that are
in service. See Note 4 and
Note 9.
1.4?This specification includes criteria for choice of raw material, together with performance requirements and test methods for determining conformance with the requirements. 1.5?Quality-control measures are to be taken by manufacturers. See Appendix X4 for general information on quality control. 1.6?UnitsThe values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7?The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||
|
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-05-07 (Počet položiek: 2 897 585)
© Copyright 2024 NORMSERVIS s.r.o.