Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F645-15a

Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems (Includes all amendments And changes 4/4/2018).

Automaticky preložený názov:

Štandardné Sprievodca pre výber, dizajn, a inštalácia termoplastického Zásobovanie vodou Tlakové potrubné systémy

NORMA vydaná dňa 15.5.2015

Jazyk
Prevedenie	Online zabezpečené PDF - 77.90 € Tlačené - 77.90 €
Dostupnosť	SKLADOM
Cena	77.90 € bez DPH
77.90 €

Informácie o norme:

Označenie normy: ASTM F645-15a
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.5.2015
Kód tovaru: NS-610048
Počet strán: 13
Približná hmotnosť: 39 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty

Anotácia textu normy ASTM F645-15a :

Keywords:

design, disinfecting, field repair, inspection, installation, joints, pressure piping, service line, testing, thermoplastic, water ,, ICS Number Code 23.040.20 (Plastic pipes)

Doplňujúce informácie

Significance and Use

4.1 The requirements of this specification are intended to provide information to select, design and install thermoplastic, water-pressure piping systems for use outside buildings. Materials covered in this specification are Poly(Vinyl Chloride) (PVC) and Polyethylene (PE) plastic pipe fittings.

1. Scope

1.1 This guide is intended for use in the selection, design, and installation of thermoplastic water systems for use outside buildings. For specific projects, a thorough review of this guide is recommended for the purpose of selecting specific materials, methods of joining, system design factor, and any special procedures deemed necessary to assure a satisfactory system.

1.2 It is recommended that governing codes and project specifications be consulted prior to the use of this guide. Nothing in this guide should be construed as recommending practices or systems at variance with governing codes and project specifications.

1.3 Units-The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The pipe, fittings, and joining materials shall meet the requirements of one or more of the following component product standards listed in 1.3.1 through 1.3.4 to the extent applicable. Those pipe standards followed by (a) are outside diameter-controlled pipes. Those followed by (b) are inside diameter-controlled pipes.

1.3.1 For poly(vinyl chloride) (PVC) plastic piping components:

Title of Specification

ASTM
Designation

Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80
and 120 (a)

D1785

Poly(Vinyl Chloride) (PVC) Plastic Pipe (SDR-PR) (a)

D2241

Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings,
Schedule 80

D2464

Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
40

D2466

Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Pipe
Fittings, Schedule 80

D2467

Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Pipe
and Fittings

D2564

Bell-End Poly(Vinyl Chloride) (PVC) Pipe (a)

D2672

Poly(Vinyl Chloride) (PVC) Plastic Tubing (a)

D2740

Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Line
Couplings

D3036

Joints for Plastic Pressure Pipes Using Flexible Elastomeric
Seals

D3139

Elastomeric Seals (Gaskets) for Joining Plastic Pipe

F477

PVC and ABS Injected Solvent Cemented Plastic Pipe
Joints

F545

1.3.2 For Chlorinated Poly(Vinyl chloride) (CPVC) plastic piping components:

Title of Specification

ASTM
Designation

Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 (a)

F441/F441M

Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F439

Solvent Cements for Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe and Fittings

F493

1.3.3 For polyethylene (PE) plastic piping components:

Title of Specification

ASTM
Designation

Polyethylene (PE) Plastic Pipe, (SDR-PR) (b)

D2239

Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

D2609

Socket-Type Polyethylene Fittings for Outside Diameter-
Controlled Polyethylene Pipe (

D2683

Polyethylene (PE) Plastic Tubing (a)

D2737

Polyethylene (PE) Plastic Pipe (SDR-PR) Based on
Controlled Outside Diameter (a)

D3035

Butt Heat Fusion Polyethylene (PE) Plastic Fittings for
Polyethylene (PE) Plastic Pipe and Tubing

D3261

1.3.4 For poly(vinyl chloride) (PVC) and polyethylene (PE) Plastic Piping Components Issued By the American Water Works Association:

C900 Poly(Vinyl Chloride) (PVC) Pressure Pipe,

4-inch through 12-inch, for Water (a)

C901 Polyethylene (PE) Pressure Pipe, Tubing

and Fittings, ¹/₂-inch through 3-inch, for Water

1.3.5 Pipes with wall thicknesses less than 1.50 mm (0.06 in.) are not recommended.

1.4 Other Joining Devices—Joining devices other than those covered by the listed standards may be selected by the user on the basis of his own engineering evaluation and service experience.

1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D3035-22	Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
D3036-73	Specification for Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Line Couplings (Withdrawn 1985)
D3139-19	Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals
D3261-24	Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
F412-23	Standard Terminology Relating to Plastic Piping Systems
F545-95	Specification for PVC and ABS Injected Solvent Cemented Plastic Pipe Joints (Withdrawn 2001)
F493-22	Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
F1498-08(2020)	Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
C651	Disinfecting Water Mains
C900	Poly(Vinyl Chloride) (PVC) Pressure Pipe, 4-Inch Through 12-Inch, for Water
C901	Polyethylene (PE) Pressure Pipe, Tubing and Fittings, 12-Inch Through 3-Inch, for Water
PPI-TR3	HDB/PDB/SDB/MRS Policies
PPI-TR4	HDB/SDB/PDB/MRS Listed Materials
PPI-TR9	Recommended Design Factors and Design Coefficients for Thermoplastic Pressure Pipe
NSF/ANSI Standard No. 14	for Plastic Piping Components and Related Materials Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
NSF/ANSI Standard No. 61	for Drinking Water Systems ComponentsHealth Effects
Uni-Bell Handbook of PVC Pipe	, Chapter VIII, Table 8.7
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1784-20	Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
D1785-21a	Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 (Includes all amendments and changes 10/8/2021).
D2239-22	Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
D2241-20	Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
D2464-23	Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
D2564-20	Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2609-21	Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
D2672-20e1	Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement (Includes all amendments and changes 2/12/2021).
D2683-20	Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
D2737-22	Standard Specification for Polyethylene (PE) Plastic Tubing
D2740-89	Specification for Polyvinyl Chloride (PVC) Plastic Tubing (Withdrawn 1989)
D2774-21a	Standard Practice for Underground Installation of Thermoplastic Pressure Piping (Includes all amendments and changes 10/6/2021).
D2466-23	Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
D2467-20	Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
F439-19	Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
F441/F441M-23	Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
D2855-20	Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets