Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F641-98a 10.10.1998 náhľad

Doplňujúce informácie

ASTM F641-98a

Standard Specification for Implantable Epoxy Electronic Encapsulants (Includes all amendments And changes 8/16/2017).

Automaticky preložený názov:

Štandardné špecifikácie pre implantovateľných Epoxidové elektronické zalievacie hmoty

NORMA vydaná dňa 10.10.1998

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 64.00 € Tlačené - 64.00 €
Dostupnosť	SKLADOM
Cena	64.00 € bez DPH
64.00 €

Informácie o norme:

Označenie normy: ASTM F641-98a
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.10.1998
Kód tovaru: NS-55987
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F641-98a :

Keywords:

Electronic encapsulants, Epoxy (EP) plastics-surgical implants, Implants, Pacemakers, Pulse generators, RF receivers, Telemetry devices, implantable epoxy electronic encapsulants, spec

Doplňujúce informácie

1. Scope

1.1 This specification covers thermoset plastics based on diglycidyl ethers of bisphenol A and amino functional curing agents or amine catalysts.

1.2 The epoxy encapsulants covered by this specification are intended to provide a tissue-compatible protective covering for implantable medical devices such as pulse generators, telemetry devices and RF receivers. The biocompatibility of epoxy plastics has not been established. Epoxy plastic is a generic term relating to the class of polymers formed from epoxy resins, certain curing agents or catalysts and various additives. Since many compositions and formulations fall under this category, it is essential that the fabricator assure safety of implantability of the specific composition or formulation for the intended use by current state-of-the-art test methods. This specification can be used as a basis for standardized evaluation of biocompatibility for such implantable encapsulants.

1.3 The encapsulants covered by this specification are for use in devices intended as long-term implants.

1.4 Limitations- This specification covers only the initial qualification of epoxy encapsulants for implantable electronic circuitry. Some of the requirements are not applicable to routine lot to lot quality control.

2. Referenced Documents

D149-20	Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
ISO 10993	Biological Evaluation of Medical Devices Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
D257-14(2021)e1	Standard Test Methods for DC Resistance or Conductance of Insulating Materials (Includes all amendments and changes 5/6/2021).
D570-22	Standard Test Method for Water Absorption of Plastics
D638-22	Standard Test Method for Tensile Properties of Plastics
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D1042-22	Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture
D1239-22a	Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals (Includes all amendments and changes 9/12/2022).
D1434-23	Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D2471-99	Standard Test Method for Gel Time and Peak Exothermic Temperature of Reacting Thermosetting Resins (Withdrawn 2008)
D2562-94(2015):2015/ADJD2562	Adjunct to D2562 Practice for Classifying Visual Defects in Parts Molded from Reinforced Thermosetting Plastics
D2566-86	Test Method for Linear Shrinkage of Cured Thermosetting Casting Resins During Cure
D2734-23	Standard Test Methods for Void Content of Reinforced Plastics
D3137-81(2018)	Standard Test Method for Rubber Property´Hydrolytic Stability
F74-73(1989)	Practice for Determining Hydrolytic Stability of Plastic Encapsulants for Electronic Devices (Withdrawn 1994)
F135-76(1991)	Test Method for Embedment Stress Caused by Casting Compounds on Glass-Encased Electronic Components (Withdrawn 1997)
F602-09(2015)	Standard Criteria for Implantable Thermoset Epoxy Plastics
F748-16	Standard Practice for Selecting Generic Biological Test Methods for Materials and Devices
F895-11(2016)	Standard Test Method for Agar Diffusion Cell Culture Screening for Cytotoxicity
F981-23	Standard Practice for Assessment of Muscle and Bone Tissue Responses to Long-Term Implantable Materials Used in Medical Devices
EOS-D	E-O Sterilization Standard Available from Association for Advancement of Medical Instrumentation, 1500 Wilson Blvd., Suite 417, Arlington, VA 22209.
D150-22	Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.