Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F606-14

Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

Automaticky preložený názov:

Štandardné skúšobné metódy pre stanovenie mechanických vlastností zvonka i vo vnútri závitových spojov, podložky, Direct napínacie ukazovateľoch, a nity

NORMA vydaná dňa 1.7.2014

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 87.80 € Tlačené - 87.80 €
Dostupnosť	SKLADOM
Cena	87.80 € bez DPH
87.80 €

Informácie o norme:

Označenie normy: ASTM F606-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2014
Kód tovaru: NS-55866
Počet strán: 16
Približná hmotnosť: 48 g (0.11 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F606-14 :

Keywords:

compression load, hardness, proof load, properties, tensile, testing, yield, ICS Number Code 21.060.01 (Fasteners in general)

Doplňujúce informácie

1. Scope

1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets.

1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements. In the absence of any specified test requirement(s), these test methods shall apply.

1.3 These test methods describe mechanical tests for determining the following properties:

Section

For Externally Threaded Fasteners:

Product Hardness

3.1

Proof Load

3.2.1

Method 1, Length Measurement

3.2.3

Method 2, Yield Strength

3.2.4

Method 3, Uniform Hardness

3.2.5

Axial Tension Testing of Full-Size Product

3.4

Wedge Tension Testing of Full-Size Product

3.5

Tension Testing of Machined Test Specimens

3.6

Total Extension at Fracture Test
Single Sheer Test

3.7
3.8

For Internally Threaded Fasteners:

Product Hardness

4.1

Proof Load Test

4.2

Cone Proof Load Test

4.3

For Washers and Direct Tension Indicators:

Product Hardness-General Requirements

5.1

Through Hardened Washers

5.2

Carburized Washers

5.3

Stainless Steel and Nonferrous Washers

5.4

Direct Tension Indicators

5.5

Compression Load

5.6

For Rivets:

Product Hardness

6.1

Test for Embrittlement of Metallic-Coated Externally Threaded Fasteners

Test Method for Determining Decarburization and Carburization

1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

Note 1: A complete metric companion to Test Methods F606 has been developed—F606M; therefore, no metric equivalents are shown in these test methods.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

F2328-17(2022)	Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
E10-23	Standard Test Method for Brinell Hardness of Metallic Materials
E8/E8M-24	Standard Test Methods for Tension Testing of Metallic Materials
E4-21	Standard Practices for Force Calibration and Verification of Testing Machines
A394-08(2024)	Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare
MIL STD?1312,	Test 13 and Test 20
F959-15	Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
F606M-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric) (Withdrawn 2015)
E384-22	Standard Test Method for Microindentation Hardness of Materials
E83-23	Standard Practice for Verification and Classification of Extensometer Systems
E18-22	Standard Test Methods for Rockwell Hardness of Metallic Materials
F1624-12(2018)	Standard Test Method for Measurement of Hydrogen Embrittlement Threshold in Steel by the Incremental Step Loading Technique
F436-11	Standard Specification for Hardened Steel Washers
E92-23	Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.