Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F593-13a

Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs (Includes all amendments And changes 8/30/2016).

Automaticky preložený názov:

Štandardné špecifikácie pre nerezovými skrutkami, Hex Cap skrutky, a skrutky

NORMA vydaná dňa 1.12.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 68.60 € Tlačené - 68.60 €
Dostupnosť	SKLADOM
Cena	68.60 € bez DPH
68.60 €

Informácie o norme:

Označenie normy: ASTM F593-13a
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2013
Kód tovaru: NS-55813
Počet strán: 9
Približná hmotnosť: 27 g (0.06 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Svorníky, šrouby, závrtné šrouby

Anotácia textu normy ASTM F593-13a :

Keywords:
bolts, general use, hex cap screws, stainless, studs, ICS Number Code 21.060.10 (Bolts, screws, studs)

Doplňujúce informácie

Significance and Use

13.1 For the purposes of determining compliance with the specified limits for properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.

1. Scope

1.1 This specification covers the requirements for stainless steel bolts, hex cap screws, and studs 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

1.2 Seven groups of stainless steel alloys are covered, including thirteen austenitic, two ferritic, four martensitic, and one precipitation hardening.

Group

Alloys^A

Condition^B

304, 305, 384, 304 L,

(CW) cold worked^C

18-9LW, 302HQ^D

316, 316 L

(CW) cold worked^C

321, 347

(CW) cold worked^C

430^E

(CW) cold worked^C

410^F

(H) hardened and tempered

431

(H) hardened and tempered

630

(AH) age hardened

1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the manufacturer and the purchaser at the time of the inquiry and order.

1.4 Suitable nuts for use with bolts, hex cap screws, and studs included in this specification are covered by Specification F594. Unless otherwise specified, all nuts used on these fasteners shall conform to the requirements of Specification F594, shall be of the same alloy group, and shall have a specified minimum proof stress equal to or greater than the specified minimum full-size tensile strength of the externally threaded fastener.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

A380-06	Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
A484/A484M-24	Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings
B1.1	Unified Inch Screw Threads

F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
D3951-18(2023)	Standard Practice for Commercial Packaging
A967-05	Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts
A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A582/A582M-22	Standard Specification for Free-Machining Stainless Steel Bars
F594-22	Standard Specification for Stainless Steel Nuts
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
A262-15(2021)	Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A493-23	Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
A555/A555M-23	Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods
A564/A564M-19a	Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes (Includes all amendments and changes 4/2/2021).
A276-13	Standard Specification for Stainless Steel Bars and Shapes
A342/A342M-21	Standard Test Methods for Permeability of Weakly Magnetic Materials