Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Norma ASTM F467-13(2018) 1.9.2018 náhľad

Doplňujúce informácie

ASTM F467-13(2018)

Standard Specification for Nonferrous Nuts for General Use

NORMA vydaná dňa 1.9.2018

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 58.80 € Tlačené - 58.80 €
Dostupnosť	SKLADOM
Cena	58.80 € bez DPH
58.80 €

Informácie o norme:

Označenie normy: ASTM F467-13(2018)
Dátum vydania normy: 1.9.2018
Kód tovaru: NS-897826
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Matice

Anotácia textu normy ASTM F467-13(2018) :

This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications. Materials shall be tested and shall conform to the chemical composition, hardness, proof stress, proof load, and tensile stress requirements.

Keywords:
general use, nonferrous, nuts ,, ICS Number Code 21.060.20 (Nuts)

Doplňujúce informácie

Significance and Use

11.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.

1. Scope

1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service applications.

1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F468.

1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

Note 1: This specification is the inch-pound companion to Specification F467M; therefore, no SI equivalents are presented in the specification.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

B?18.2.2	Square and Hex Nuts
E101-91	Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-To-Plane Technique (Withdrawn 1996)
E54-80(1996)	Standard Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)
E55-23	Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75-76(1996)	Standard Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E76-88(1998)	Standard Test Methods for Chemical Analysis of Nickel-Copper Alloys (Withdrawn 2003)
E92-23	Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials
D3951-18(2023)	Standard Practice for Commercial Packaging
E18-22	Standard Test Methods for Rockwell Hardness of Metallic Materials
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34-11	Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E38-85	Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys (Withdrawn 1989)
B154-16(2022)	Standard Test Method for Mercurous Nitrate Test for Copper Alloys
B574-23	Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod and Bar
E53-07	Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E120-00	Standard Test Methods for Chemical Analysis of Titanium and Titanium Alloys (Withdrawn 2003)
E165-09	Standard Practice for Liquid Penetrant Examination for General Industry
E227-90(1996)	Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn 2002)
E354-21e1	Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys (Includes all amendments and changes 2/23/2022).
E478-08(2017)	Standard Test Methods for Chemical Analysis of Copper Alloys
E1409-13(2021)	Standard Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by Inert Gas Fusion
F468-23	Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
B?1.1	Unified Inch Screw Threads (UN and UNR Thread Form)

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.