Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F432-95

Standard Specification for Roof and Rock Bolts and Accessories

Automaticky preložený názov:

Štandardné špecifikácie pre strešné a svorníky a príslušenstvo

NORMA vydaná dňa 1.1.2001

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 87.50 € Tlačené - 87.50 €
Dostupnosť	SKLADOM
Cena	87.50 € bez DPH
87.50 €

Informácie o norme:

Označenie normy: ASTM F432-95
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.2001
Kód tovaru: NS-55269
Počet strán: 15
Približná hmotnosť: 45 g (0.10 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F432-95 :

Keywords:

bolting materials, iron bolting materials, rock, rock bolts/accessories, roofing membranes, steel bolting materials-bolts, roof and rock bolts/accessories

Doplňujúce informácie

1. Scope

1.1 This specification covers the chemical, mechanical, and dimensional requirements for roof and rock bolts and accessories. Addressed in this specification are double-end threaded and slotted steel bars; fully grouted bolts and threaded bars; mechanical anchorage devices used for point anchorage applications; roof truss systems; partially grouted deformed bolts; formable anchorage devices; and other frictional anchorage devices. All of these products represent various designs used for ground support systems. This specification can be revised to address new technologies.

1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 This hazard statement applies only to Section 10, Test Methods of this specification. This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D6637-11	Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
B?18.2.2	Square and Hex Nuts
F436-11	Standard Specification for Hardened Steel Washers
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
B?1.1	Unified Screw Threads
A29/A29M-23	Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought
A47/A47M-99(2022)e1	Standard Specification for Ferritic Malleable Iron Castings (Includes all amendments and changes 10/7/2022).
B?1.3M	Screw Thread Gaging Systems for Dimensional Acceptability--Inch and Metric Screw Threads
A194/A194M-23	Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both
A220/A220M-99(2022)e1	Standard Specification for Pearlitic Malleable Iron (Includes all amendments and changes 10/7/2022).
A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products
A416/A416M-24	Standard Specification for Low-Relaxation, Seven-Wire Steel Strand for Prestressed Concrete
A536-84(2019)e1	Standard Specification for Ductile Iron Castings (Includes all amendments and changes 5/3/2019).
A563-15	Standard Specification for Carbon and Alloy Steel Nuts
A615/A615M-22	Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A882/A882M-20	Standard Specification for Filled Epoxy-Coated Seven-Wire Steel Prestressing Strand
A1011/A1011M-23	Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength
A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products
D1248-16	Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.