Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for High Strength Structural Bolts, Steel and Alloy Steel, Heat Treated, 120 ksi (830 MPa) and 150 ksi (1040 MPa) Minimum Tensile Strength, Inch and Metric Dimensions
Automaticky preložený názov:
Štandard Specification pre dosiahnutie vysokej pevnosti skrutky, a zliatinovej ocele, tepelne spracované, 120 KSI (830 MPa) a 150 KSI (1040 MPa) Minimálna pevnosť v ťahu, Inch a metrické rozmery
NORMA vydaná dňa 1.1.2015
Označenie normy: ASTM F3125-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.2015
Kód tovaru: NS-54957
Počet strán: 13
Približná hmotnosť: 39 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
alloy steel, alternate design fasteners, bolts, carbon steel, fasteners, heavy hex bolt, inch, metric, spline end, steel, structural, structural bolts, tension control bolt, twist-off bolt, weathering steel,, ICS Number Code 21.060.10 (Bolts, screws, studs)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers chemical, physical and mechanical requirements for quenched and tempered bolts manufactured from steel and alloy steel, in inch and metric dimensions, in two strength grades, two types and two styles. 1.1.1 This specification is a consolidation and replacement of six ASTM standards, including; A325, A325M, A490, A490M, F1852 and F2280. 1.1.2 This consolidated standard is to ensure alignment between standards with the same intended end use and to simplify the use and maintenance of structural bolt specifications. 1.2 Intended Use: 1.2.1 Bolts manufactured under this specification are intended for use in structural connections covered in the Specification for Structural Joints Using High-Strength Bolts, as approved by the Research Council on Structural Connections. 1.2.2 Bolts in this specification are furnished in sizes from 1/2 to 1-1/2 in. inclusive and from M12 to M36 inclusive. 1.3 Classification: 1.3.1 Bolts are designated by grade or property class, which indicates inch or metric respectively. 1.3.2 Bolts are designated by type denoting raw material chemical composition. 1.3.3 Bolts are designated by style denoting Heavy Hex bolts or “Twist-Off” Style assemblies.
1.4 Terms used in this specification are defined in F1789. 1.5 Units—The values stated in either SI units or inch pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 Table footnotes are requirements. Notes are advisory. 1.7 The following safety hazard caveat pertains to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2025-03-13 (Počet položiek: 2 232 199)
© Copyright 2025 NORMSERVIS s.r.o.