Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F3101-21

Standard Specification for Unsupervised Public Use Outdoor Fitness Equipment

NORMA vydaná dňa 1.3.2021

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 97.40 € Tlačené - 97.40 €
Dostupnosť	SKLADOM
Cena	97.40 € bez DPH
97.40 €

Informácie o norme:

Označenie normy: ASTM F3101-21
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2021
Kód tovaru: NS-1030583
Počet strán: 25
Približná hmotnosť: 75 g (0.17 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F3101-21 :

Keywords:
outdoor fitness equipment, public use,, ICS Number Code 97.220.40 (Outdoor and water sports equipment)

Doplňujúce informácie

1. Scope

1.1?This specification establishes parameters for the design and manufacture of outdoor fitness equipment as defined in 3.1.30.

1.2?It is intended that these fitness products will be used in an unsupervised outdoor setting or environment and will be permanently anchored.

1.2.1?It is the intent of this specification to only specify requirements for outdoor fitness equipment and its installation and not the design of the facility or grounds on which the products are to be installed.

1.3?The specifications set forth in this standard are intended to minimize the likelihood of serious injuries.

1.3.1?The specifications set forth in this standard are for outdoor fitness equipment intended for use in an unsupervised setting by individuals age 13 and older.

1.4?The values stated in SI (metric) units are to be regarded as standard. The values in parentheses are for information only.

1.5?General Measures, Tolerances, and Conversions:?

1.5.1?The general tolerances for this specification (unless otherwise specified) are as follows:

Dimension

Tolerance

X mm (X in.)

? 13.0 mm (0.5 in.)

X.X mm (X.X in.)

?1.3 mm (0.05 in.)

X.XX mm (X.XX in.)

?.0.130 mm (0.005 in.)

1.5.2?These tolerances still apply to a dimension even when terms like greater than, less than, minimum, or maximum are used.

1.6?This standard is to be used in conjunction with Test Methods F2571 and Specification F2276. If a design or installation concern is not addressed in this specification then the applicable requirements of Specification F2276 shall be used.

1.6.1?This standard takes precedence over Specification F2276 and Test Methods F2571 in areas that are addressed in this document.

1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
F1159-16e1	Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards (Includes all amendments and changes 6/3/2021).
F846-92(1998)	Standard Guide for Testing Performance of Amusement Rides and Devices
F853-05	Standard Practice for Maintenance Procedures for Amusement Rides and Devices (Withdrawn 2014)
F893-10	Standard Guide for Inspection of Amusement Rides and Devices
F963-23	Standard Consumer Safety Specification for Toy Safety
F1004-23	Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures
F3021-17	Standard Specification for Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments
F2571-15(2020)	Standard Test Methods for Evaluating Design and Performance Characteristics of Fitness Equipment
F2276-23	Standard Specification for Fitness Equipment
F1951-21	Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment
F1749-15(2020)	Standard Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels
F1292-22	Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment
F1077-05	Standard Guide for Selection of Committee F16 Fastener Specifications (Withdrawn 2014)
F3022-16e1	Standard Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments (Includes all amendments and changes 7/7/2017).
F1918-21	Standard Safety Performance Specification for Soft Contained Play Equipment
F698-94(2000)	Standard Specification for Physical Information to be Provided for Amusement Rides and Devices (Withdrawn 2009)

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.