Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM F2968/F2968M-21
Standard Specification for Crosslinked Polyethylene (PEX) Pipe for Gas Distribution Applications
NORMA vydaná dňa 1.5.2021
Informácie o norme:
Označenie normy: ASTM F2968/F2968M-21
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2021
Kód tovaru: NS-1024087
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Trubky z plastické hmoty
Potrubí a potrubní spojky
Systémy dodávky plynu v budovách
Anotácia textu normy ASTM F2968/F2968M-21 :
Keywords:
crosslinked polyethylene, gas distribution, HDB, hydrostatic stress, metric, PEX, pipe, PPI, pressure,, ICS Number Code 23.040.20 (Plastic pipes),23.100.40 (Piping and coupling),91.140.40 (Gas supply systems)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This specification covers outside diameter controlled, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe, made in pipe dimension ratios ranging from 6 to 17, and pressure rated for gas distribution. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, minimum operating temperature and squeeze-off. Requirements for pipe markings are also given. The pipe covered by this specification is intended for buried gas distribution and gas transmission pressure piping applications. 1.2?This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (specified in Specification F3373). Fittings to be used with PEX pipe manufactured to this specification are in Specification F2829/F2829M. Installation considerations are in X3.2. Note 1:?Inch-sized fittings should not be used for
metric-sized pipe, and metric-sized fittings should not be used for
inch-sized pipe.
1.3?The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
