Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications
NORMA vydaná dňa 1.5.2021
Označenie normy: ASTM F2905/F2905M-21
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2021
Kód tovaru: NS-1024086
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Trubky z plastické hmoty
Potrubí a potrubní spojky
Zařízení pro ropný průmysl a průmysl zemního plynu obecně
Keywords:
crosslinked polyethylene, gas gathering, HDB, hydrostatic stress, metric, PEX, pipe, PPI, pressure,, ICS Number Code 23.040.20 (Plastic pipes),23.100.40 (Piping and coupling),75.180.01 (Equipment for petroleum and natural gas industries in general)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||
1.1?This specification covers outside diameter controlled, pressure rated, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, and minimum operating temperature. Requirements for pipe markings are also given. The pipe covered by this specification is intended for pressure or non-pressure oil and gas producing applications, such as conveying oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover piping for gas distribution applications. 1.2?This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (specified in Specifications F1055 or F3373). Fittings to be used with PEX pipe manufactured to this Specification are in Specification F2829/F2829M. Installation considerations are in Appendix X3. 1.3?The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Note 1:?Metric sized (SI units) pipe should only be joined
with corresponding metric sized fittings, and inch sized pipe
should only be joined with corresponding inch sized fittings. Inch
sized fittings should not be used for metric sized pipe, and metric
sized fittings should not be used for IPS inch sized
pipe.
1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||
|
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-09-05 (Počet položiek: 2 346 132)
© Copyright 2024 NORMSERVIS s.r.o.