Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F2763-11

Standard Specification for 30 to 60 in. [750 to 1500 mm] Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

Automaticky preložený názov:

Štandardné špecifikácie pre 30-60 palcov [750 - 1500 mm] Triple profilu Wall Polyetylén (PE) rúrky a armatúry pre splaškové vody aplikácie

NORMA vydaná dňa 1.2.2011

Jazyk
Prevedenie	Online zabezpečené PDF - 73.30 € Tlačené - 73.30 €
Dostupnosť	SKLADOM
Cena	73.30 € bez DPH
73.30 €

Informácie o norme:

Označenie normy: ASTM F2763-11
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.2.2011
Kód tovaru: NS-54493
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Kanalizační systémy

Anotácia textu normy ASTM F2763-11 :

Keywords:

fittings, interior liner, PE, pipe, polyethylene, profile wall, sanitary sewer, ICS Number Code 91.140.80 (Drainage systems)

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements and test methods for triple profile wall polyethylene pipe and fittings. The nominal inside diameters covered are 30 to 60 in. [750 to 1500 mm].

1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.

1.3 This specification covers pipe and fittings with an essentially smooth interior and exterior wall using an annular corrugated profile middle wall (Fig. 1).

1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

LRFD, Section 12	AASHTO LRFD Bridge Design Specifications Section 12 Buried Structures and Tunnel Liners
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
MIL-STD-129
NCHRP Report 631	Updated Test and Design Methods for Thermoplastic Drainage Pipe
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D3212-21	Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
D4218-20	Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
F412-23	Standard Terminology Relating to Plastic Piping Systems
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
F2136-18(2024)	Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
D578/D578M-23	Standard Specification for Glass Fiber Strands
A666-23	Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D618-21	Standard Practice for Conditioning Plastics for Testing
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

Podobné normy:

ASTM A888-13a

Historická
1.6.2013

ASTM B788/B788M-09(2..

Historická
1.5.2014

ASTM B789/B789M-99(2..

Historická
1.5.2011

ASTM C1131-10e1

Historická
1.12.2010

ASTM F1417-11a

Historická
1.8.2011

ASTM F2764/F2764M-11..

Historická
1.5.2011

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.