ASTM F2393-12
ASTM F2401-04(2010)..
ASTM F2423-11
ASTM F2428-04(2011)..
ASTM F2451-05(2010)..
ASTM F2502-11
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM F2527-10
Standard Specification for Wrought Seamless and Welded and Drawn Cobalt Alloy Small Diameter Tubing for Surgical Implants (UNS R30003, UNS R30008, UNS R30035, UNS R30605, and UNS R31537)
Automaticky preložený názov:
Štandard Specification pre Zámočníctvo bezšvíkové a zvárané a ťahané Cobalt Alloy malý priemer trubice pre chirurgické implantáty (UNS R30003, UNS R30008, UNS R30035, UNS R30605 a UNS R31537)
NORMA vydaná dňa 1.12.2010
Informácie o norme:
Označenie normy: ASTM F2527-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2010
Kód tovaru: NS-54070
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM F2527-10 :
Keywords:
cobalt alloy, small diameter, metals (for surgical implant), surgical applications, tubing, surgical implants, tubing, Cobalt alloys (for surgical implants)--specifications, Surgical implants--specifications, Tubing, UNS R30003, UNS R30008, UNS R30035 (Co-Ni-Cr-Mo alloy, MP-35-N), UNS R30605 (Co-Cr-Ni-W alloy, L-605), UNS R31537 (Co-Cr-Mo alloy), ICS Number Code 11.040.40 (Implants for surgery, prothetics and orthotics)
Doplňujúce informácie
| 1. Scope | ||||
|
1.1 This specification covers the requirements for wrought seamless and welded and drawn cobalt alloy small diameter tubing used for the manufacture of surgical implants. Material shall conform to the applicable requirements of Specifications F90, F562, F688, F1058 or F1537, Alloy 1. This specification addresses those product variables that differentiate small diameter medical tubing from the bar, wire, sheet and strip product forms covered in these specifications. 1.2 This specification applies to straight length tubing with 6.3 mm [0.250 in.] and smaller nominal outside diameter (OD) and 0.76 mm [0.030 in.] and thinner nominal wall thickness. 1.3 The specifications in 2.1 are referred to as the ASTM material standard(s) in this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. |
||||
| 2. Referenced Documents | ||||
|
Podobné normy:
Historická
1.3.2012
Historická
1.5.2010
Historická
1.7.2011
Historická
1.7.2011
Historická
1.9.2010
Historická
1.6.2011
Doporučujeme:
