Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F2510/F2510M-07(2013) 1.2.2013 náhľad

Doplňujúce informácie

ASTM F2510/F2510M-07(2013)

Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated High Density Polyethylene Drainage Pipes

Automaticky preložený názov:

Štandard Specification na elastické konektory medzi železobetón prielez konštrukciou a vlnitej High Density Rúry polyetylénovej drenážne

NORMA vydaná dňa 1.2.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.30 € Tlačené - 70.30 €
Dostupnosť	SKLADOM
Cena	70.30 € bez DPH
70.30 €

Informácie o norme:

Označenie normy: ASTM F2510/F2510M-07(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.2.2013
Kód tovaru: NS-54033
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Vnější systémy odvádění odpadní vody

Anotácia textu normy ASTM F2510/F2510M-07(2013) :

Keywords:

corrugated HDPE pipe, design test method, hydrostatic testing, leakage tests, manholes, resilient connectors, seals, ICS Number Code 93.030 (External sewerage systems)

Doplňujúce informácie

1. Scope

1.1 This specification covers the design, material, and minimum performance requirements of resilient connectors used for connections between reinforced concrete structures conforming to Specifications C478 and C913 to annular corrugated profile wall high density polyethylene (HDPE) drainage pipe conforming to AASHTO M252 or Specification F2306/F2306M.

1.1.1 These connectors are designed to provide a positive seal between the pipe and manholes or other structures subjected to internal and external hydrostatic pressures less than 10.8 psi [74 KPa].

1.1.2 Testing under this standard is limited to hydrostatic pressures. Alternate air and vacuum pressure testing involve unique testing protocols and are not addressed under this standard.

1.1.3 Testing under this standard is conducted in a laboratory as a proof of design certification. Actual field performance testing would be accomplished and accepted under individual project performance standards or pipeline acceptance criteria, which is outside the scope of this standard.

1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 The following precautionary caveat pertains only to the test methods portion, Section 7. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precaution statement, see 7.2.3.

2. Referenced Documents

F2306/F2306M-21	Standard Specification for 300 mm to 1500 mm [12 in. to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Non-Pressure Gravity-Flow Storm Sewer and Subsurface Drainage Applications

A493-23	Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
C822-21	Standard Terminology Relating to Concrete Pipe and Related Products
A666-23	Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
C913-23	Standard Specification for Precast Concrete Water and Wastewater Structures
D624-00(2020)	Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D746-20	Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
D1566-21a	Standard Terminology Relating to Rubber (Includes all amendments and changes 11/10/2021).
F412-23	Standard Terminology Relating to Plastic Piping Systems
C478-19	Standard Specification for Circular Precast Reinforced Concrete Manhole Sections