Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Norma ASTM F2408-16(2023) 1.2.2023 náhľad

Doplňujúce informácie

ASTM F2408-16(2023)

Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets

NORMA vydaná dňa 1.2.2023

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 63.40 € Tlačené - 63.40 €
Dostupnosť	SKLADOM
Cena	63.40 € bez DPH
63.40 €

Informácie o norme:

Označenie normy: ASTM F2408-16(2023)
Dátum vydania normy: 1.2.2023
Kód tovaru: NS-1103005
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Vnější části staveb

Anotácia textu normy ASTM F2408-16(2023) :

This specification establishes the minimum requirements for coated tubular picket ornamental fence systems fabricated from galvanized steel components. Steel material for tubular picket ornamental fence system structural components shall be galvanized by the hot-dip process, either after forming, or prior to forming. Powder coatings applied to the exterior surface of fence components shall be polymer material: polyester or epoxy and polyester combinations. Wet coating applied to the exterior surface of fence components shall be a two-coat paint application system (one coat of epoxy, polyester or polyurethane primer; one coat of polyester, polyurethane, or acrylic liquid). Fittings, fasteners, and decorative accessories for ornamental steel fence systems shall be manufactured with a material and finish coating that meets the same protective coating performance requirements as required for panels and posts. Four structural test methods shall be conducted: Method A which is application of horizontal concentrated load, Method B which is application of vertical concentrated load, Method C which is application of horizontal thrust load to infill areas, and Method D which is application of horizontal cone penetration load. Different tests shall also be performed in order to determine the following properties of the fence system coatings: adhesion, corrosion resistance, impact resistance, and weathering resistance.

Keywords:

architectural metal fence, iron fence, ornamental fence system, ornamental iron fence, ornamental metal fence, ornamental steel fence, picket fence, steel picket fence, tubular picket fence, vertical tube fence, wrought iron fence,, ICS Number Code 91.090 (External structures)

Doplňujúce informácie

1. Scope

1.1?This specification establishes the minimum requirements for coated tubular picket ornamental fence systems fabricated from galvanized steel components.

1.2?The requirements of this specification do not apply to vertical bar fence systems utilizing solid bar or wrought iron materials.

1.3?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

A653/A653M-23	Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
D2244-23	Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
A1011/A1011M-23	Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength
B117-19	Standard Practice for Operating Salt Spray (Fog) Apparatus
D523-14(2018)	Standard Test Method for Specular Gloss
A239-21	Standard Practice for Locating the Thinnest Spot in a Zinc (Galvanized) Coating on Iron or Steel Articles
D714-02(2017)	Standard Test Method for Evaluating Degree of Blistering of Paints
D1654-08(2016)e1	Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments (Includes all amendments and changes 5/3/2017).
A1008/A1008M-23e1	Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable (Includes all amendments and changes 12/29/2023).
D2794-93(2024)	Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
D3359-23	Standard Test Methods for Rating Adhesion by Tape Test
D822-23	Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings
F2814-23	Standard Guide for Design and Construction of Ornamental Steel Picket Fence Systems for Security Purposes
E4-21	Standard Practices for Force Calibration and Verification of Testing Machines

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.